Siemens SINUMERIK 802D sl Manuel de l'opérateur télécharger pdf (Page 98)

Overview of alarms 06/2009

NCK alarms

2-98

SINUMERIK 802D sl, Diagnostics Manual, 06/2009

Index == 6: Program SIRELAY command in synchronized action

Index == 7: Program GOTOF/GOTOB/GOTO command with block number or label

Index == 8: Load COA application "cutting generator"

Program Con-

tinuation:

Clear alarm with the RESET key. Restart part program

14092 [Channel %1: ] Block %2 axis %3 is wrong axis type

Parameters: %1 = Channel number

%2 = Block number, label

%3 = Axis name, spindle number

Definitions: One of the following programming errors has occurred:

1. The keyword WAITP(x) "Wait with block change until the specified positioning axis has reached its

end point" has been used for an axis that is not a positioning axis.

2. G74 "Reference point approach from the program" has been programmed for a spindle. (Only axis

addresses are permitted).

3. The keyword POS/POSA has been used for a spindle. (The keywords SPOS and SPOSA must be

programmed for spindle positioning).

4. If the alarm occurs with the "Rigid tapping" function (G331), the following causes are conceivable:

- The master spindle is not in position-controlled mode.

- Incorrect master spindle

- Master spindle without encoder

5. An axis name was programmed which no longer exists (e.g. when using axial variables as an

index). Or NO_AXIS has been programmed as an index.

6. If 14092 is output as a note with alarm 20140 Motion-synchronous action: traversing of command

axis, the following causes are possible:

- The axis is currently being traversed by the NC program already.

- An overlaid movement is active for the axis.

- The axis is active as following axis of a coupling.

- An interpolation compensation such as a temperature compensation is active for the axis.

Reaction: Correction block is reorganized.

Interface signals are set.

Alarm display.

Remedy: - Correct the part program according to which of the above errors is involved.

- Program SPOS.

- Set the correct master spindle with SETMS.

Program Con-

tinuation:

Clear alarm with NC START or RESET key and continue the program.

14095 [Channel %1: ] Block %2 radius for circle programming too small

Parameters: %1 = Channel number

%2 = Block number, label

Definitions: The radius entered for radius programming is too small, i.e. the programmed radius is smaller than

half of the distance between start and end point.

Reaction: Correction block is reorganized.

Interface signals are set.

Alarm display.

Remedy: Modify part program.

Program Con-

tinuation:

Clear alarm with NC START or RESET key and continue the program.

14096 [Channel %1: ] Block %2 illegal type conversion

Parameters: %1 = Channel number

%2 = Block number, label

Definitions: During the program run, a variable value assignment or an arithmetic operation has caused data to

be processed in such a way that they have to be converted to another type. This would lead to the

value range being exceeded.

Value ranges of the various variable types:

- REAL: Property: Fractional number with dec. pt., value range: +/-(2-1022-2+1023)

- INT: Property: Integers with signs, value range: +/-(231-1)

- BOOL: Property: Truth value TRUE, FALSE, value range: 0,1

- CHAR: Property: 1 ASCII character, value range: 0-255

- STRING: Property: Character string (max. 100 values), value range: 0-255

1 2 ... 93 94 95 96 97 98 99 100 101 102 103 ... 339 340

Siemens SINUMERIK 802D sl Manuel de l'opérateur Page 98

Commentaires sur ces manuels

Siemens SINUMERIK 802D sl Manuel de l'opérateur Page 98

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Siemens SINUMERIK 802D sl