Siemens SINUMERIK 802D sl Manuel de l'opérateur télécharger pdf (Page 215)

Cycle alarms

06/2009 Overview of alarms

2-215

SINUMERIK 802D sl, Diagnostics Manual, 06/2009

61211 [Channel %1: ] Block %2: Absolute reference missing

Parameters: %1 = Channel number

%2 = Block number, label

Definitions: An incremental indication was made, but the absolute reference is unknown.

Alarm triggered by following cycles: E_MI_CON, E_MI_PL, E_PI_CIR, E_PI_REC, E_PO_CIR,

E_PO_REC, E_PS_CIR, E_PS_HIN, E_PS_MRX, E_PS_POL, E_PS_SEQ, E_PS_XYA, E_SL_CIR,

E_SL_LON, F_PS_CIR, F_PS_MRX, F_PS_SEQ

Reaction: Interpreter stop

NC Start disable in this channel.

Interface signals are set.

Alarm display.

Remedy: Program an absolute position prior to using incremental indications.

Program Con-

tinuation:

Clear alarm with the RESET key. Restart part program

61212 [Channel %1: ] Block %2: Wrong tool type

Parameters: %1 = Channel number

%2 = Block number, label

Definitions: The tool type is not suitable for machining.

Alarm triggered by following cycles: CYCLE92, CYCLE951, E_DR, E_DR_O1, E_DR_PEC,

E_DR_SIN, E_MI_TXT, F_DR, F_DR_PEC, F_DR_SIN, F_DRILL, F_DRILLC, F_DRILLD,

F_DRM_DR, F_DRM_PE, F_DRM_SI, F_GROOV, F_MI_TXT, F_MT_LEN, F_PARTOF, F_ROU_Z,

F_ROUGH, F_SP_EF, F_TAP, F_TR_CON, F_UCUT_T

Reaction: Interpreter stop

NC Start disable in this channel.

Interface signals are set.

Alarm display.

Remedy: Select a new tool type.

Program Con-

tinuation:

Clear alarm with the RESET key. Restart part program

61213 [Channel %1: ] Block %2: Circle radius too small

Parameters: %1 = Channel number

%2 = Block number, label

Definitions: The programmed circle radius is too small.

Alarm triggered by following cycles: CYCLE77, E_CR_HEL, E_PI_CIR, E_PO_CIR, E_PO_REC,

F_PI_CIR, F_PO_CIR, F_PO_REC

Remedy: Correct the circle radius, center point or end point.

61214 [Channel %1: ] Block %2: No pitch programmed

Parameters: %1 = Channel number

%2 = Block number, label

Definitions: No thread/helical pitch has been entered.

Alarm triggered by following cycles: E_CR_HEL, E_PO_CIR, E_PO_REC, F_PO_CIR, F_PO_REC.

Reaction: Interpreter stop

NC Start disable in this channel.

Interface signals are set.

Alarm display.

Remedy: Program a pitch.

Program Con-

tinuation:

Clear alarm with the RESET key. Restart part program

61215 [Channel %1: ] Block %2: Unfinished dimension incorrectly programmed

Parameters: %1 = Channel number

%2 = Block number, label

Definitions: Check the blank spigot dimensions. The blank spigot must be larger than the production part spigot.

Alarm triggered by following cycles: CYCLE76, CYCLE77, E_PI_CIR, E_PI_REC, E_PO_CIR,

E_PO_REC, F_PI_CIR, F_PI_REC, F_PO_CIR, F_PO_REC

Remedy: Check parameters _AP1 and _AP2.

1 2 ... 210 211 212 213 214 215 216 217 218 219 220 ... 339 340

Commentaires sur ces manuels

Pas de commentaire

Siemens SINUMERIK 802D sl Manuel de l'opérateur Page 215

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Siemens SINUMERIK 802D sl