Siemens SINUMERIK 802D sl Manuel de l'opérateur télécharger pdf (Page 66)

Overview of alarms 06/2009

NCK alarms

2-66

SINUMERIK 802D sl, Diagnostics Manual, 06/2009

Definitions: During contour segmentation (activated with the keyword CONTPRON), the field for the contour table

has been detected as too small. For every permissible contour element (circle or straight line) there

must be a row in the contour table.

Reaction: Local alarm reaction.

NC Start disable in this channel.

Interface signals are set.

Alarm display.

Remedy: Base the definition of the field variables of the contour table on the contour elements to be expected.

The contour segmentation divides some NC blocks into as many as 3 machining cuts. Example: N100

DEF TABNAME_1 [30, 11] Field variables for the contour table provide for 30 machining cuts. The

number of columns (11) is a fixed quantity.

Program Con-

tinuation:

Clear alarm with the RESET key. Restart part program

10962 [Channel %1: ] Block %2 function %3 not possible with path correction

Parameters: %1 = Channel number

%2 = Block number, label

%3 = Funktionsname

Definitions: With this software release, the specified function can not yet be used together with tool radius com-

pensation. Please modifiy the part program or obtain a higher software version.

Reaction: Correction block is reorganized.

Local alarm reaction.

Interface signals are set.

Alarm display.

NC Stop on alarm at block end.

Remedy: Modify part program.

Program Con-

tinuation:

Clear alarm with NC START or RESET key and continue the program.

12000 [Channel %1: ] Block %2 address %3 programmed repeatedly

Parameters: %1 = Channel number

%2 = Block number, label

%3 = Source string of the address

Definitions: Most addresses (address types) may only be programmed once in an NC block, so that the block infor-

mation remains unambiguous (e.g. X... T... F... etc. - exception: G and M functions).

Reaction: Correction block is reorganized.

Interface signals are set.

Alarm display.

Remedy: Press the NC Stop key and select the function "Correction block" with the softkey PROGRAM COR-

RECT. The correction pointer positions on the incorrect block.

- Remove from the NC program addresses that occur more than once (except for those where multiple

value assignments are allowed).

- Check whether the address (e.g. the axis name) is specified via a user-defined variable (this may not

be easy to see if allocation of the axis name to the variable is performed in the program through com-

putational operations only).

Program Con-

tinuation:

Clear alarm with NC START or RESET key and continue the program.

12010 [Channel %1: ] Block %2 address %3 address type programmed too often

Parameters: %1 = Channel number

%2 = Block number, label

%3 = Source string of the address

Definitions: The number of times each address type may occur in a NC block is defined internally (for instance, all

axes together form one address type to which a block limit also applies).

Reaction: Correction block is reorganized.

Interface signals are set.

Alarm display.

Remedy: Press the NC Stop key and select the function "Correction block" with the softkey PROGRAM COR-

RECTION. The correction pointer positions on the incorrect block.

The program information must be split up over several blocks (but make sure that the functions are of

the non-modal type!).

1 2 ... 61 62 63 64 65 66 67 68 69 70 71 ... 339 340

Commentaires sur ces manuels

Pas de commentaire

Siemens SINUMERIK 802D sl Manuel de l'opérateur Page 66

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Siemens SINUMERIK 802D sl