Siemens SINUMERIK 802D sl Manuel de l'opérateur télécharger pdf (Page 213)

Cycle alarms

06/2009 Overview of alarms

2-213

SINUMERIK 802D sl, Diagnostics Manual, 06/2009

61198 [Channel %1: ] Block %2: no swiveling in JOG --> several active basic

frames(G500) contain rotations

Parameters: %1 = Channel number

%2 = Block number, label

Definitions: Alarm triggered by following cycles: CYCLE800.

Reaction: Interpreter stop

NC Start disable in this channel.

Interface signals are set.

Alarm display.

Remedy: --

Program Con-

tinuation:

Clear alarm with the RESET key. Restart part program

61199 [Channel %1: ] Block %2: approach of tool and swivel data record

change (TOOLCARRIER) not allowed

Parameters: %1 = Channel number

%2 = Block number, label

Definitions: Alarm triggered by following cycles: CYCLE800.

Reaction: Interpreter stop

NC Start disable in this channel.

Interface signals are set.

Alarm display.

Remedy: --

Program Con-

tinuation:

Clear alarm with the RESET key. Restart part program

61200 [Channel %1: ] Block %2: Too many elements in machining block

Parameters: %1 = Channel number

%2 = Block number, label

Definitions: The machining block contains too many elements.

Alarm triggered by following cycles: CYCLE76, CYCLE77, E_CALL, E_DR, E_DR_BGF, E_DR_BOR,

E_DR_O1, E_DR_PEC, E_DR_REA, E_DR_SIN, E_DR_TAP, E_MI_TR, E_PI_CIR, E_PI_REC,

E_PO_CIR, E_PO_REC, E_PS_CIR, E_PS_FRA, E_PS_HIN, E_PS_MRX, E_PS_POL,

E_PS_ROW, E_PS_SEQ, E_PS_XYA, E_SL_LON, F_DR, F_DR_PEC, F_DR_REA, F_DR_SIN,

F_DR_TAP, F_MI_TR, F_PI_CIR, F_PI_REC, F_PO_CIR, F_PO_REC, F_PS_CIR, F_PS_MRX,

F_PS_ROW, F_PS_SEQ, F_SL_LON

Remedy: Check the machining block, delete some elements, if required.

61201 [Channel %1: ] Block %2: Wrong sequence in machining block

Parameters: %1 = Channel number

%2 = Block number, label

Definitions: The sequence of elements in the machining block is invalid.

Alarm triggered by following cycles: E_CP_CE, E_CP_DR, E_MANAGE, F_CP_CE, F_CP_DR,

F_MANAGE.

Reaction: Interpreter stop

NC Start disable in this channel.

Interface signals are set.

Alarm display.

Remedy: Sort the sequence in the machining block.

Program Con-

tinuation:

Clear alarm with the RESET key. Restart part program

61202 [Channel %1: ] Block %2: No technology cycle

Parameters: %1 = Channel number

%2 = Block number, label

Definitions: No technology cycle was programmed in the machining block.

Alarm triggered by following cycles: E_MANAGE, F_MANAGE.

Reaction: Interpreter stop

NC Start disable in this channel.

Interface signals are set.

1 2 ... 208 209 210 211 212 213 214 215 216 217 218 ... 339 340

Commentaires sur ces manuels

Pas de commentaire

Siemens SINUMERIK 802D sl Manuel de l'opérateur Page 213

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Siemens SINUMERIK 802D sl