Siemens SINUMERIK 802D sl Spécifications Page 286
- Page / 392
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Overview of alarms 06/2007
Cycle alarms
2-286
" Siemens AG 2007 All Rights Reserved
SINUMERIK 802D sl, Diagnostics Manual, 06/2007 Edition
61193 Channel %1 block %2: compressor option not set up
Parameters: %1 = Channel number
%2 = Block number, label
Definitions: The alarm is triggerd by the following cycles: CYCLE832.
Reaction: Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy: --
Program Con-
tinuation:
Clear alarm with the RESET key. Restart part program
61194 Channel %1 block %2: spline interpolation option not set up
Parameters: %1 = Channel number
%2 = Block number, label
Definitions: The alarm is triggerd by the following cycles: CYCLE832.
Reaction: Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy: --
Program Con-
tinuation:
Clear alarm with the RESET key. Restart part program
61197 Channel %1 block %2: no swiveling in JOG --> active WO G%4 and basic
frames contain rotations
Parameters: %1 = Channel number
%2 = Block number, label
Definitions: Alarm triggered by following cycles: CYCLE800.
Reaction: Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy: --
Program Con-
tinuation:
Clear alarm with the RESET key. Restart part program
61198 Channel %1 block %2: no swiveling in JOG --> several active basic
frames(G500) contain rotations
Parameters: %1 = Channel number
%2 = Block number, label
Definitions: Alarm triggered by following cycles: CYCLE800.
Reaction: Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy: --
Program Con-
tinuation:
Clear alarm with the RESET key. Restart part program
61199 Channel %1 block %2: approach of tool and swivel data record change
(TOOLCARRIER) not allowed
Parameters: %1 = Channel number
%2 = Block number, label
Definitions: Alarm triggered by following cycles: CYCLE800.
Reaction: Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
- SINUMERIK 802D sl 1
- SINUMERIK® Documentation 2
- General alarms 7
- Table of Contents 1 9
- Overview of alarms 2 13
- Overview of alarms 06/2007 40
- NCK alarms/ISO alarms 40
- Example: 102
- 2: Base frame 189
- Reaction: Alarm display 189
- - Axis replacement 192
- Reaction: Interpreter stop 197
- tool was selected before 202
- Program Con 203
- %3 = T number of first tool 203
- ($AA_TOFF) is cleared 238
- 2.2 Cycle alarms 269
- > "Spindles" 298
- Cycle alarms 331
- 06/2007 Overview of alarms 331
- 2.3 Profibus alarms 332
- Profibus alarms 337
- 2.4 PLC alarms 338
- 2.5 SINAMICS-Parameters 340
- List of action numbers 3 341
- Remedy 365
- System reactions on alarms 4 367
- Cancel criteria for alarms 370
- Appendix A 373
- Appendix 06/2007 374
- Abbreviations 374
- 06/2007 Appendix 375
- 06/2007 Index 389
- (OHFWURQLFGRFXPHQWDWLRQ 392
- 8VHUGRFXPHQWDWLRQ 392
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Siemens SINUMERIK 802D sl
(150 pages)
(184 pages)Puls CD5.243 manuels
Manuels d'utilisation et guides de l'utilisateur pour Accessoires pour les appareils électriques Puls CD5.243.
Nous fournissons des manuels en pdf 1 Puls CD5.243 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Commentaires sur ces manuels