Siemens FIREFINDER-XLS Spécifications télécharger pdf (Page 6)

s Industry, Inc.

Building Technologies Division

FireFinder XLS Components ─ (cont.’d)

RNI Remote Network Interface

The Remote Network Interface (Model RNI) provides a

connection point for use with equipment mounted in a

remote-lobby enclosure on the FireFinder XLS FACP.

Model RNI is used to provide additional input, output and

control features to the system remotely, via the main

control panel. These additional features may include control

switches and indicators: (Models SCM-8, LCM-8 and

FCM-6), remote-emergency paging microphones or

telephones: (Models LVM, FMT), or controls used in

graphic annunciators (Models SIM16, OCM-16) or system-

status display with the ability to acknowledge alarms,

silence audibles and reset the system (Model SSD-C-

REM). Model RNI allows Model PMI to be mounted in the

Model REMBOX2 or Model REMBOX4 remote lobby

enclosure.

RPM Remote Printer Module

The Remote Printer Module (Model RPM) provides a means

of connecting the FireFinder XLS system to a printer,

such as Model PAL-1, for creating a hard copy of system

status and configuration reports. Simultaneously, Model

RPM provides an output port that can be configured to

communicate with external systems.

System-Status Display

SSD-Series System-Status Display

The System Status Display (SSD-series model displays) is

a remote LED / LCD display that shows the local status of a

FireFinder XLS system. An LED illuminates when Alarm,

Supervisory, Trouble, and Security events occur on the

system. A (4) four-line liquid-crystal display (LCD) will

give details of the event in alphanumeric form.

The display can be toggled to display additional events.

Optional remote system control capabilities are available.

Models SSD-C, SSD-C-INT, and Model SSD-C-REM have three

(3) additional control buttons to acknowledge events,

silence audible circuits, and reset the system.

Models SSD-C and SSD-C-INT have an integral keyswitch

that enables these control buttons to operate.

Model SSD-C-REM is located within a locked cabinet.

Hence, no additional keyswitch is required for enabling

the control buttons.

CAB1 Single Row Enclosure

Model CAB 1, the smallest of the FireFinder XLS

enclosures, can house a single Model CAB-MP cabinet

mounting plate for mounting card cages, power supplies

and bulk amplifiers. Model CAB1 also has four (4)

mounting slots on the inner door for mounting Model PM

and Model

ID-MP switch module brackets.

Model CAB1 comes complete with a black back box; black

inner and outer doors; a single lock and key set on the outer

door; a single, installed cabinet mounting plate (Model

CAB-MP), and a single, installed outer door lens plate

(Model OD-LP). A red version (Model CAB1-R) is also

available – approximate size: 27" (68.6cm.) high, 26"

(66cm.) wide, and 8" (20.3cm.) deep.

MDACT - Multi-Point Digital Alarm

Communicator Transmitter

MDACT - Multi-Point Digital Alarm Communicator

Transmitter

The Multi-Point Digital Alarm Communicator Transmitter

(Model MDACT) is used in FireFinder XLS systems where

point identification of Alarm, Supervisory, Security and

Trouble events is required at Central or Remote Receiving

Stations. An intelligent RS-485 communications protocol

transmits all system information to Model MDACT.

The installer selects the specific event or groups of

events that are set to transmit from Model MDACT over

phone lines to listed receiving station equipment. In

turn, Model MDACT can transmit point information, via the

Ademco Contact ID and the SIA protocol. A Mounting Plate

(Model MOM2-XMP), MOM-2 card cage, and an XMI

Interface Card are required for installation.

1 2 3 4 5 6 7 8 9 10 11 12

Commentaires sur ces manuels

Pas de commentaire

Siemens FIREFINDER-XLS Spécifications Page 6

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Siemens FIREFINDER-XLS