Siemens FIREFINDER-XLS Spécifications télécharger pdf (Page 4)

s Industry, Inc.

Building Technologies Division

FireFinder XLS Components ─ (cont.’d)

CRC-6 Controllable Relay Card

The Controllable Relay Card (Model CRC-6) is used with

the FireFinder XLS FACP. Model CRC-6 is designed to

provide auxiliary control of building functions, such as:

door-holder release, elevator capture, smoke control, lock

release, etc. Model CRC-6 plugs into one (1) slot in the

Model CC-5 or Model CC-2 card cage. Model CRC-6

provides six (6), fully programmable relays. Each relay

contains one (1) set of SPDT contacts rated at 4 Amps 30

VDC / 120VAC resistive and 3.5 amps 120VAC inductive (0.6

P.F.)

SIM-16 Supervised Input Module

The Supervised input Module (Model S

IM-16) is a

remotely located, general-purpose input module. Model

IM-16 provides 16 input circuits for remote system

monitoring. Each input can be individually programmed

as supervised (dry-contact only) or unsupervised (general-

purpose input.) Model S

IM-16 has two (2) Form C relays.

The relays and inputs are programmed using the Zeus

system software-programming tool.

CDC-4 Conventional Detector Card

The Conventional Detector Card (Model CDC-4) is used

to monitor Siemens Fire Safety conventional detectors

on the FireFinder XLS system. Model CDC-4 can be

used in applications where conventional detectors are

more suited than addressable detectors, such as

hallways or large meeting rooms. Also, Model CDC-4

can be used to upgrade Siemens conventional fire-alarm

panels to the FireFinder XLS system without requiring

detector replacement.

CC-2 Card Cage-2 Slots CC-5 Card Cage-5 Slots

CC-5 / CC-2 Card Cages

The Models CC-5 / CC-2 card cages provide the physical

mounting location and all wiring connection points for all

fire-and-voice system options cards for the FireFinder XLS

system. Model CC-5 has five (5) slots, while Model CC-2

has two (2) slots.

All cards plugged into the CC-5 / CC-2 card cage

communicate with other FireFinder-XLS modules via a

common data bus. Connectors are provided on the left and

right side of the CC-5 to connect a 60-pin cable for

communications with the FireFinder-XLS' operator interface,

power supplies and amplifiers modules.

Field wiring to devices and circuits terminates on the

Models CC-5 / CC-2 card cages. All cards designed for use

with the Models CC-5 / CC-2 route their field wiring

terminations to the ‘top’ of the Model CC-5 / CC-2 card

cages. These connections are all power limited. Internal

wiring connections distribute 24VDC to cards or high-level

audio signals (depending on application used) connect to

the ‘bottom’ of the Model CC-5 / CC-2 card cages. These

connections are all non-power limited.

All wiring connections to the Model CC-5 / CC-2 card cages

are to removable terminal blocks. Terminal blocks are rated

for use with wire sized 12AWG to 24AWG. Each connector is

numbered to make wiring terminations to the correct

position on the terminal block simple in order to reduce

potential wiring errors.

SCM-8 Switch Control Module

The Switch Control Module (Model SCM-8) is a FireFinder

XLS-option module that provides manual control to the

Emergency Voice Evacuation System (EVAC) or manual

fire-system control. Each Model SCM-8 module provides

eight (8) momentary push-button switches and 16

light-emitting diodes (LEDs) to indicate their status.

Each switch is assigned two (2) LEDs, as well as a label

to indicate the switch's programmed usage. The label

slides behind a clear protective membrane. One of the

LEDs assigned to each switch is a dual-colored LED,

which is used to indicate what type of signal is active.

1 2 3 4 5 6 7 8 9 10 11 12

Commentaires sur ces manuels

Pas de commentaire

Siemens FIREFINDER-XLS Spécifications Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Siemens FIREFINDER-XLS