Siemens FIREFINDER-XLS Spécifications télécharger pdf (Page 3)

s Industry, Inc.

Building Technologies Division

FireFinder XLS Components ─ (cont.’d)

Each circuit can be independently programmed for use

with listed audible or visual notification appliances, listed

emergency audio speakers, municipal tie boxes, leased

lines, or as releasing circuits. Model Z

IC-4A plugs into one

(1) slot in the Model CC-5 or Model CC-2 card cage, and has

on-board LEDs for system status and troubleshooting.

Indication of power, communication, internal operation,

and ground-fault conditions are provided, as well as

indication of circuit activation or Trouble conditions.

ZIC-8B / ZIC-2C Zone Indicating Cards

ZIC-8B / ZIC-2C

The Zone

Indicating Card (Model ZIC-8B) provides eight (8)

fully supervised, programmable output circuits for use on

the FireFinder XLS f

ire-alarm control panel (FACP). Model

IC-8B supplies eight (8) Class B (Style Y) type output

circuits, power limited to 2.0 amps maximum per circuit.

Each circuit can be independently programmed for use

with listed audible or visual notification appliances, or

listed emergency audio speakers. Model Z

IC-8B plugs

into one (1) slot in the Model CC-5 or Model CC-2 card

cage, and has on-board LEDs for system status and

troubleshooting.

Model ZIC-2C mounts directly on Model ZIC-8B, and

allows each of the Model Z

IC-8B output circuits to be used

for two-channel voice applications.

Indication of power,

communication, internal operation, and ground-fault

conditions are provided, as well as indication of circuit

activation or trouble conditions.

NIC-C Network I nterface Card

NIC-C Network Interface Card

The Network

Interface Card (Model NIC-C) provides HNET or

XNET network communications between enclosures.

addition to the HNET or XNET communication, Model N

IC-C

provides CAN network communication within an enclosure

or external to the enclosure. HNET or XNET communication

can be wired Style 4 or Style 7, but the CAN network can

be wired Style 4 only.

When used for HNET communications, Model N

IC-C

provides communication between enclosures on a single

system.

When Model N

IC-C is used for XNET communications,

Model N

IC-C provides communication between systems.

The maximum of XNET Model N

IC-C cards on a single

system (single node) is one (1), for a total of 64 XNET

Model NIC-C cards on a peer-to-peer networked system.

Model N

IC-C has diagnostic LEDs that indicate: Card Fail,

CAN Fail, HNET Fail, XNET Fail, Ground Fault, Loop ‘A’ Fail and

Loop ‘B’ Fail. Model N

IC-C Card also has LEDs to indicate

Power, Style and Active Networks.

HLIM Line Isolator Module

The loop-isolator module (Model HL

IM) provides short-

circuit protection on FireFinder XLS intelligent device

circuits (see: Model DLC). When Model HL

IM detects a

short circuit, Model HL

IM is able to isolate the affected

segment of the circuit – allowing the remaining devices

to continue operation. Model HL

IM is self-restoring –

automatically reconnecting to circuit segment when the

fault is removed. Model HL

IM can be wired in either a

Style 4 or Style 6 configuration.

Model HL

IM does not occupy a device address on the Model

DLC circuit, and does not require programming. Up to 15

Model HL

IM modules may be installed on each Model DLC

loop.

HCP Control Point Module

Model HCP provides an intelligent control point for the

FireFinder XLS Control Panel. Model HCP can be

programmed as an independent, remotely located tele-

phone zone, speaker zone or notification appliance

circuit. Model HCP is designed to be used with the

Siemens – Fire Safety Notification-Appliance Circuits

product line.

Model HCP communicates through the Model DLC

analog loop, and can be wired either Class A (Style Z) or

Class B (Style Y). The 24 VDC power input comes from

either the control panel or from any

UL Listed power-

limited, auxiliary-power supply.

1 2 3 4 5 6 7 8 ... 11 12

Commentaires sur ces manuels

Pas de commentaire

Siemens FIREFINDER-XLS Spécifications Page 3

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Siemens FIREFINDER-XLS