Siemens TC63 Manuel d'utilisateur Page 448
- Page / 501
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
TC63 AT Command Set
19.6 AT^SSYNC
s
TC63_ATC_V00.490 Page 448 of 501 5/24/05
Confidential / Draft - Do not copy
19.6.1 ME status indicated by status LED patterns
The following table lists the possible patterns of status LED behavior, and describes the ME operating status indi-
cated by each pattern if AT^SSYNC parameter <mode>=1 and <mode>=2.
Table 19.1: Modes of the LED and indicated ME functions
LED behavior ME operating status if AT^SSYNC=1 ME operating status if AT^SSYNC=2
Permanently off ME is in one of the following modes:
POWER DOWN mode, AIRPLANE
mode, CHARGE ONLY mode, SLEEP
mode with no wake-up event is
progress.
ME is in one of the following modes:
POWER DOWN mode, AIRPLANE
mode, CHARGE ONLY mode.
600 ms on / 600ms off Limited Network Service: No SIM card
inserted or no PIN entered, or network
search in progress, or ongoing user
authentication, or network login in
progress.
This applies no matter whether the ME
works at full functionality level
AT+CFUN=1 or has entered a "tempo-
rary wake-up state" during one of the
CYCLIC SLEEP modes.
Same as for AT^SSYNC=1
75 ms on / 3 s off IDLE mode: The mobile is registered to
the GSM network (monitoring control
channels and user interactions). No call
is in progress.
The same LED pattern applies when the
ME enters a "temporary wake-up state
during one of the CYCLIC SLEEP
modes (e.g. after characters have been
received on the serial interface).
Same as for AT^SSYNC=1
75 ms on / 75 ms off /
75 ms on / 3 s off
One or more GPRS contexts activated. Same as for AT^SSYNC=1
500 ms on / 25 ms off Packet switched data transfer in
progress.
Same as for AT^SSYNC=1
Permanently on Depending on type of call:
Voice call: Connected to remote party.
Data call: Connected to remote party or
exchange of parameters while setting
up or disconnecting a call.
This applies no matter whether the ME
works at full functionality level
AT+CFUN=1 or in one of the CYCLIC
SLEEP modes where it wakes up only
temporarily to make the call.
Same as for AT^SSYNC=1
n * 600 ms on / n * 600 ms
off
Not possible: With AT^SSYNC=1, LED
signalization is disabled in SLEEP
mode.
SLEEP mode is activated (AT+CFUN
parameter <fun> ≠ 1), but the ME is not
registered to the GSM network (e.g. SIM
not inserted or PIN not entered, and
therefore, either no network service or
only Limited Network Service is avail-
able.
- AT Command Set 1
- Contents 3
- TC63 AT Command Set 10
- List of Tables 12
- List of Figures 13
- 1. Introduction 14
- 1.2 Related documents 15
- 1.3 Document conventions 16
- 1.3.1 Quick reference table 16
- 1.4 AT Command Syntax 18
- 1.4.1 Using Parameters 18
- 1.5 Supported character sets 20
- 1.9 Errors and Messages 29
- 2. Configuration Commands 30
- 2.2.1 AT&V responses 32
- 3. Status Control Commands 66
- 3.2 AT+CIND Indicator control 68
- 4.1 AT\Q Flow control 89
- 4.5 ATE Enable command echo 93
- 4.9.1 Autobauding 101
- 5. Security Commands 108
- 5.4 AT+CLCK Facility lock 118
- 5.5 AT^SLCK Facility lock 123
- 5.6 AT+CPWD Change Password 124
- 5.7 AT^SPWD Change Password 128
- 5.8 AT^SCSL Customer SIM Lock 130
- 6. Identification Commands 134
- 7. Call related Commands 140
- 7.2 ATA Answer a call 141
- 7.10 AT+CHUP Hang up call 151
- 7.29 ATP Select pulse dialing 178
- 7.30 ATT Select tone dialing 178
- 8. Network Service Commands 179
- 8.5 AT+CSQ Signal quality 187
- 8.6 AT^SMONC Cell Monitoring 188
- 8.7 AT^SMOND Cell Monitoring 190
- 8.8.1 AT^MONI responses 194
- 8.8.2 Service states 195
- 8.9.1 AT^MONP responses 197
- 8.10 AT^SMONG GPRS Monitor 198
- 8.12 AT^SHOM Display Homezone 202
- 9.5 AT+CCUG Closed User Group 212
- 9.7 AT+CCWA Call Waiting 218
- 10. Internet Service Commands 235
- Remote Client 257
- 11. GPRS Commands 268
- 12. FAX Commands 311
- 12.4 AT+FRM Receive Data 314
- 12.5 AT+FRS Receive Silence 315
- 12.7 AT+FTM Transmit Data 317
- 13.1 SMS parameters 319
- 13.7 AT+CMGS Send SMS message 331
- 14. SIM related Commands 363
- 15.3 Related AT Commands 384
- 16.2 ^SSTN SAT Notification 388
- 16.4 AT^SSTR SAT Response 390
- 17. Phonebook Commands 391
- 17.2 AT+CNUM Read own numbers 392
- 18. Audio Commands 411
- 18.5 AT+CMUT Mute control 414
- 18.6 AT+VTD Tone duration 415
- 19. Hardware related Commands 436
- 19.2 AT+CALA Set alarm time 437
- 19.7.4 Example: Using I²C Bus 456
- 20. Miscellaneous Commands 457
- 21. Appendix 462
Produits connexes et manuels pour Matériel Siemens TC63
Matériel Siemens 54 Manuel d'utilisateur
(56 pages)
(56 pages)
Matériel Siemens 300 Manuel d'utilisateur
(64 pages)
(64 pages)
Matériel Siemens CL-110-I Manuel d'utilisateur
(129 pages)
(129 pages)
Matériel Siemens CP 1515 Manuel d'utilisateur
(299 pages)
(299 pages)
Matériel Siemens I-SURF Manuel d'utilisateur
(70 pages)
(70 pages)
Matériel Siemens C2-010 Manuel d'utilisateur
(51 pages)
(51 pages)
Matériel Siemens TC35 Manuel d'utilisateur
(39 pages)
(39 pages)
Matériel Siemens TC35i Manuel d'utilisateur
(37 pages)
(37 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.101 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels