Siemens TC63 Manuel d'utilisateur Page 270
- Page / 501
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
TC63 AT Command Set
11.2 AT+CGANS
s
TC63_ATC_V00.490 Page 270 of 501 5/24/05
Confidential / Draft - Do not copy
11.2 AT+CGANS Manual response to a network request for PDP con-
text activation
Syntax
Command Description
The write command requests the MT to respond to a network request for GPRS PDP context activation which
has been signaled to the TE by the RING or CRING unsolicited result code. The <response> parameter allows
the TE to accept or reject the request.
Parameter Description
[0] the request is rejected and the MT returns OK to the TE
1 accept and request that the PDP context be activated
a string parameter which indicates the layer 2 protocol to be used (see AT+CGDATA command)
a numeric parameter which specifies a particular PDP context definition (see AT+CGDCONT command).
Note
• If <response> is 1, the following procedure is followed by the MT:
If the <L2P> parameter value is unacceptable to the MT, the MT will return an ERROR or +CME ERROR
response. Otherwise, the MT issues the intermediate result code CONNECT and enters V.250 online data
state.
A <cid> may be specified for use in the context activation request.
During the PDP startup procedure the MT has the PDP type and the PDP address provided by the network
in the Request PDP context activation message. If this is in conflict with the information provided by a spec-
ified <cid>, the command will fail. There will be no conflict, if the PDP type matches exactly and the PDP
address given by the context definition for <cid> is empty or matches exactly with the address specified with
the network PDP context activation message.
The context will be activated using the values for PDP type and address provided by the network, together
with all other information found in the PDP context definition. An APN may or may not be required, depending
on the application.
Test Command
AT+CGANS=?
Response(s)
+CGANS: (list of supported <response>s), (list of supported <L2P>s)
OK
Write Command
AT+CGANS=[<response>[, <L2P>[, <cid>]]]
Response(s)
CONNECT
NO CARRIER
ERROR
+CME ERROR
Reference(s) PIN ASC0 ASC1 USB MUX1 MUX2 MUX3 Charge 4 Last
GSM 07.07 % % % % % % % ! ! %
<response>
(num)
<L2P>
(str)
<cid>
(num)
- AT Command Set 1
- Contents 3
- TC63 AT Command Set 10
- List of Tables 12
- List of Figures 13
- 1. Introduction 14
- 1.2 Related documents 15
- 1.3 Document conventions 16
- 1.3.1 Quick reference table 16
- 1.4 AT Command Syntax 18
- 1.4.1 Using Parameters 18
- 1.5 Supported character sets 20
- 1.9 Errors and Messages 29
- 2. Configuration Commands 30
- 2.2.1 AT&V responses 32
- 3. Status Control Commands 66
- 3.2 AT+CIND Indicator control 68
- 4.1 AT\Q Flow control 89
- 4.5 ATE Enable command echo 93
- 4.9.1 Autobauding 101
- 5. Security Commands 108
- 5.4 AT+CLCK Facility lock 118
- 5.5 AT^SLCK Facility lock 123
- 5.6 AT+CPWD Change Password 124
- 5.7 AT^SPWD Change Password 128
- 5.8 AT^SCSL Customer SIM Lock 130
- 6. Identification Commands 134
- 7. Call related Commands 140
- 7.2 ATA Answer a call 141
- 7.10 AT+CHUP Hang up call 151
- 7.29 ATP Select pulse dialing 178
- 7.30 ATT Select tone dialing 178
- 8. Network Service Commands 179
- 8.5 AT+CSQ Signal quality 187
- 8.6 AT^SMONC Cell Monitoring 188
- 8.7 AT^SMOND Cell Monitoring 190
- 8.8.1 AT^MONI responses 194
- 8.8.2 Service states 195
- 8.9.1 AT^MONP responses 197
- 8.10 AT^SMONG GPRS Monitor 198
- 8.12 AT^SHOM Display Homezone 202
- 9.5 AT+CCUG Closed User Group 212
- 9.7 AT+CCWA Call Waiting 218
- 10. Internet Service Commands 235
- Remote Client 257
- 11. GPRS Commands 268
- 12. FAX Commands 311
- 12.4 AT+FRM Receive Data 314
- 12.5 AT+FRS Receive Silence 315
- 12.7 AT+FTM Transmit Data 317
- 13.1 SMS parameters 319
- 13.7 AT+CMGS Send SMS message 331
- 14. SIM related Commands 363
- 15.3 Related AT Commands 384
- 16.2 ^SSTN SAT Notification 388
- 16.4 AT^SSTR SAT Response 390
- 17. Phonebook Commands 391
- 17.2 AT+CNUM Read own numbers 392
- 18. Audio Commands 411
- 18.5 AT+CMUT Mute control 414
- 18.6 AT+VTD Tone duration 415
- 19. Hardware related Commands 436
- 19.2 AT+CALA Set alarm time 437
- 19.7.4 Example: Using I²C Bus 456
- 20. Miscellaneous Commands 457
- 21. Appendix 462
Produits connexes et manuels pour Matériel Siemens TC63
Matériel Siemens 54 Manuel d'utilisateur
(56 pages)
(56 pages)
Matériel Siemens 300 Manuel d'utilisateur
(64 pages)
(64 pages)
Matériel Siemens CL-110-I Manuel d'utilisateur
(129 pages)
(129 pages)
Matériel Siemens CP 1515 Manuel d'utilisateur
(299 pages)
(299 pages)
Matériel Siemens I-SURF Manuel d'utilisateur
(70 pages)
(70 pages)
Matériel Siemens C2-010 Manuel d'utilisateur
(51 pages)
(51 pages)
Matériel Siemens TC35 Manuel d'utilisateur
(39 pages)
(39 pages)
Matériel Siemens TC35i Manuel d'utilisateur
(37 pages)
(37 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.340 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels