Siemens S7 Manuel d'utilisateur Page 105
- Page / 222
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Configuring Communication Connections
105
SIMATIC NET NCM S7 for Industrial Ethernet
C79000-G8976-C129–06
4.4.3 Specifying ISO Transport Dynamic Properties
Dynamics Tab
The Dynamics tab displays the relevant timers and counters of this connection.
You can normally accept these default values.
If necessary, for example with connections to non-Simatic systems, you can set
the timers and counters individually and influence the dynamic response of the
connection.
Figure 4-10 Layout of the “Dynamics” Tab of the Properties Dialog
Attributes Description Access
Connection Establishment
Retransmission Time
The retransmission time specifies the interval after
which an unsuccessful connection establishment
attempt can be triggered again (1–60 s, default 5 s)
– if connection establishment is active
– if connection establishment is passive (–> irrelevant)
Modifiable
–––––
Data Transfer
Retransmission time This parameter specifies the interval after which an
unsuccessful transmission attempt can be triggered
again (100–30000 ms, default 1000 ms).
Modifiable
Max. Count Max. Count is the number of attempted transmissions
including the first (1–100, default 5).
Modifiable
- Audience 6
- Scope of this Manual 6
- Symbols used in this Manual 6
- Conventions 9
- Contents 10
- Stations 13
- 1.1 Industrial Ethernet 14
- Configuration and Diagnostics 18
- Industrial Ethernet 22
- Configuring S7 Connections 25
- Interface 27
- IP (Internet Protocol) 28
- SEND/RECEIVE interface 28
- Connection Types 30
- SIMATIC S5 30
- Configuring 31
- Networking in a Multiproject 31
- Variants 32
- Configuration of the System 33
- (Sub)Project 36
- Projects 39
- (TCP/IP) 41
- Ethernet Option 44
- 2.2 Procedure 45
- Procedure 46
- Subnet Attachment 49
- Graphic Overview in NetPro 52
- Overview in Table Form 53
- Options Tab 55
- S Assigning an IP address 56
- S Ethernet Profile for 56
- S Resetting module memory 56
- S Send Keepalives for 57
- S Multiplex OP Connections / 58
- Diagnostics Tab 59
- Addressing Tab 59
- Setting Up Connections 63
- Latest CPs) 64
- Requirements 65
- Alternative Procedure 67
- Principle 69
- Type of Interface 69
- Functions (FCs) 74
- Amounts of Data 74
- Purpose of the FCs 75
- Programming Connections 75
- 3.4 Additional Information 80
- Known Problems 81
- 4.1 Procedure 84
- 4.3 Connections 87
- Tasks of the Ethernet CP 88
- New Connection 90
- Unspecified Connections 94
- 4.3.3 Further Functions 96
- Display (Example) 98
- General Tab 100
- C79000-G8976-C129–06 101
- Address Parameters 102
- Addresses Tab 103
- TSAP Format 103
- Local and Remote TSAPs 103
- Default TSAPs 104
- Dynamics Tab 105
- Attributes AccessDescription 106
- Modifiable 106
- Display only 106
- Figure 4-11 107
- System Memory 108
- Links to Other Systems 108
- Overview Tab 109
- Introduction 110
- Opening the Dialog 110
- Address parameter 113
- Figure 4-16 116
- Figure 4-20 124
- Figure 4-21 125
- Application 134
- Figure 4-27 137
- 4.7.5 Free UDP Connection 139
- Routing to Distribute Load 140
- S7 Ethernet CPs 141
- Block Library 142
- Evaluating Status Codes 147
- Overview 148
- Working with the Job Header 151
- Meaning of the Block 152
- How the Block Works 153
- S Note the block type: 156
- S Note on the S7-400: 156
- Condition Codes 156
- DONE MeaningSTATUSERROR 158
- Example of AG_SEND 159
- NDR MeaningSTATUSERROR 166
- Caution when Configuring 167
- 5.4.1 FC7 AG_LOCK 169
- 5.4.2 FC8 AG_UNLOCK 171
- NCM S7 Diagnostics 175
- 6.1 Overview 176
- Functions 177
- Mode-Dependent Functions 177
- Installation 178
- Structure 179
- Operation 179
- 6.2.2 General Menu Commands 180
- S Dialog update time 181
- S Show TSAP in ASCII 181
- Ethernet CP 182
- Internetworking 183
- Other Startup Options 184
- 6.4 How to Use Diagnostics 185
- Firmware Loader 191
- 7.1 Application 192
- 7.2 Loading Firmware 193
- 2nd Step 194
- 3rd Step 194
- References 197
- Order Numbers 200
- Glossary 201
- B.1 General Section 202
- B.2 Industrial Ethernet 206
- B.3 PROFInet 208
- Linking to Other Systems with 211
- FETCH/WRITE 211
- “Parameter Values“ 212
- Parameter Values 214
- PI/PQ C T 215
- Document History 217
- A&D Technical Support 221
Produits connexes et manuels pour Logiciel Siemens S7
Logiciel Siemens Gigaset C675 IP Spécifications
(187 pages)
(187 pages)
Logiciel Siemens COM32 Guide de l'utilisateur
(126 pages)
(126 pages)
Logiciel Siemens SIMATIC NET Spécifications
(268 pages)
(268 pages)
Logiciel Siemens v1.0 Manuel de service
(202 pages)
(202 pages)
Logiciel Siemens S7-400 Manuel de service
(382 pages)
(382 pages)
Logiciel Siemens AC65 Guide de l'utilisateur
(123 pages)
(123 pages)
Puls CD5.243 manuels
Manuels d'utilisation et guides de l'utilisateur pour Accessoires pour les appareils électriques Puls CD5.243.
Nous fournissons des manuels en pdf 1 Puls CD5.243 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Commentaires sur ces manuels