Siemens X-400 Manuel d'utilisateur Page 84
- Page / 148
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Installation and Commissioning
Operating Instructions for SCALANCE X-400 Industrial Ethernet Switches
84 C79000-G8976-C186-03
Removing the Media Module Extender from the S7-300 Standard Rail
You require the following tools:
● slotted screwdriver with a 2.8 mm wide blade
● slotted screwdriver with a 5.5 mm wide blade
Note
To remove the extender, remove the media modules from slots 13 and 14.
When removing a media module extender from an S7-300 rail, the basic device
remains in position. Follow the steps below:
1. To remove an extender module, use a slotted screwdriver with a 5.5 mm wide
blade, to open the captive screw between slots 13 and 14 in the lower part of
the extender module.
2. Remove the cover from slot 11 of the basic device.
3. Use a slotted screwdriver with a 2.8 mm wide blade to loosen the two captive
slug screws on slot 11 of the basic device in the upper and lower recesses as
far as they will go.
4. Push the extender module slowly to the right while keeping it straight until the
two guide bolts of the extender module are completely outside the holes in the
basic device.
5. Pull out the lower part of the extender module slightly towards the front and lift
it from the S7-300 rail.
6. Replace the right side panel of the basic device so that the guide bolts fit into
the two holes in the basic device.
7. Using a slotted screwdriver with a 2.8 mm wide blade, tighten the two captive
slug screws on slot 11. The screws lock the two guide bolts, so do not use ex-
cessive force when tightening them.
8. Fit a suitable cover on slot 11 of the basic device.
Note
The basic device must not be used permanently without the right side panel.
- Trademarks 3
- 6 C79000-G8976-C186-03 6
- Preface 7
- Further Documentation 8
- Standards and Approvals 8
- Contents 9
- C79000-G8976-C186-03 10
- Introduction to 11
- Industrial Ethernet Switches 11
- 1.2 Topologies 13
- Electrical Ring 14
- Optical Ring 14
- Configuration Example 15
- 1.2.2 Star Structure 16
- 1.2.3 Line Structure 18
- SCALANCE X-400 21
- M M 4 9 2 - 2 23
- F O 2 x 1 0 0 0 23
- 2.2 Ports of SCALANCE X-400 24
- Transmission medium 25
- Transmission range 25
- Connectors 25
- 2.2.2 1000Base-TX 26
- 2.2.3 100Base-FX 27
- Transmission Range 28
- 2.2.4 1000Base-SX 29
- 2.2.5 1000Base-LX 30
- Compatibility List 31
- 32 C79000-G8976-C186-03 32
- Overview 33
- Components of the Product 35
- Signaling Contact 40
- DI Module 41
- Serial Port 43
- Ethernet Port 43
- Area of Application 44
- How It Works 44
- Diagnostics 45
- Startup Behavior 46
- 4.1 Media Modules 49
- Options for Slot 5 50
- Options for Slots 6 and 7 50
- Properties 51
- Connector 51
- 4.2 Covers, Dummy Cover 55
- CV490 2x1000 56
- Displays of the Cover 56
- CV490 2x100 57
- CV490 4x100 58
- Slot of the Dummy Cover 59
- Displays of the Dummy Cover 59
- 60 C79000-G8976-C186-03 60
- Extender Modules 61
- 66 C79000-G8976-C186-03 66
- Installing on an S7-300 Rail 68
- Dummy Cover 72
- Removing a Media Module 73
- Variants of the Covers 74
- Fitting a Cover 74
- Removing a Cover 74
- Fitting a Dummy Cover 75
- Removing a Dummy Cover 75
- Specifying the Slot Number 88
- Applying the Slot Numbers 88
- 6.5 Factory Defaults 89
- 6.6 Ports 90
- I N 3I N 4 92
- I N 5I N 8 I N 7 M 5 I N 6 93
- X 4 1 4 - 3 E 94
- 96 C79000-G8976-C186-03 96
- 6.7 Operator Controls 101
- Ring Ports in Slots 5 to 7 103
- R1 and R2 are set to OFF 104
- 6.8 LED Display 106
- Display Modes A through C 109
- Display in Display Mode D 110
- I N 1 / I N 5 111
- Display Modes A through D 112
- Port Statuses in DMode A 113
- Port Statuses in DMode B 114
- Port Statuses in DMode C 115
- Port Statuses in DMode D 116
- 6.9 Replacing the C-PLUG 117
- 6.10 Show Location 118
- Technical Specifications 119
- 122 C79000-G8976-C186-03 122
- 7.6 Extender Module EM495-8 127
- 1 0 7 , 5 128
- 1 0 9 , 5 128
- 1 1 2 , 4 128
- 7.7 Extender Module EM496-4 129
- Approvals, Certificates 131
- EMC Directive 132
- Required FDA and IEC labels 132
- Directive on Machines 133
- Installation Guidelines 133
- Note for Australia 134
- FM Approval 136
- ATEX Approval 136
- Certification 137
- 138 C79000-G8976-C186-03 138
- Glossary 139
- A&D Technical Support 147
- Nuernberg 147
- Johnson City 147
- A&D Technical Support 148
Produits connexes et manuels pour Commutateurs de réseau Siemens X-400
(296 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.957 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels