Siemens X-400 Manuel d'utilisateur Page 74
- Page / 148
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Installation and Commissioning
Operating Instructions for SCALANCE X-400 Industrial Ethernet Switches
74 C79000-G8976-C186-03
6.2.2 Fitting / Removing the Covers
Variants of the Covers
There are three variants of the covers
● CV490 2x1000
1 Gbps, electrical transmission, 2 port displays
possible slot: 5
● CV490 2x100
4 blind displays (no port displays connected to front)
possible slots: 6, 7 and extender module EM496-4 slots 12 through 15
● CV490 4x100
10/100 Mbps, electrical transmission, 4 port displays
possible slots: 9 through 11 and extender module EM495-8 slots 12, 13
Fitting a Cover
To fit a cover, you do not require any tools.
1. Place the two lower guides of the cover into the recesses at the lower edge of
the basic device. It should no longer be possible to move the cover to the side.
2. Tilt the cover at an angle towards the back until the two plastic pins at the back
top edge of the cover jut into the recesses in the basic device.
3. Press the upper part of the cover onto the basic device until the fluted middle
section of the cover is heard to click into place.
4. Secure the labeling strip on the front of the cover.
Removing a Cover
To remove a cover, you do not require any tools.
1. Press on the fluted middle section of the top of the cover next to the backplane.
2. At the same time, tilt the cover down at an angle, the two guides initially remain
in the recesses at the lower edge of the basic device.
3. Remove the cover by pulling it upwards.
- Trademarks 3
- 6 C79000-G8976-C186-03 6
- Preface 7
- Further Documentation 8
- Standards and Approvals 8
- Contents 9
- C79000-G8976-C186-03 10
- Introduction to 11
- Industrial Ethernet Switches 11
- 1.2 Topologies 13
- Electrical Ring 14
- Optical Ring 14
- Configuration Example 15
- 1.2.2 Star Structure 16
- 1.2.3 Line Structure 18
- SCALANCE X-400 21
- M M 4 9 2 - 2 23
- F O 2 x 1 0 0 0 23
- 2.2 Ports of SCALANCE X-400 24
- Transmission medium 25
- Transmission range 25
- Connectors 25
- 2.2.2 1000Base-TX 26
- 2.2.3 100Base-FX 27
- Transmission Range 28
- 2.2.4 1000Base-SX 29
- 2.2.5 1000Base-LX 30
- Compatibility List 31
- 32 C79000-G8976-C186-03 32
- Overview 33
- Components of the Product 35
- Signaling Contact 40
- DI Module 41
- Serial Port 43
- Ethernet Port 43
- Area of Application 44
- How It Works 44
- Diagnostics 45
- Startup Behavior 46
- 4.1 Media Modules 49
- Options for Slot 5 50
- Options for Slots 6 and 7 50
- Properties 51
- Connector 51
- 4.2 Covers, Dummy Cover 55
- CV490 2x1000 56
- Displays of the Cover 56
- CV490 2x100 57
- CV490 4x100 58
- Slot of the Dummy Cover 59
- Displays of the Dummy Cover 59
- 60 C79000-G8976-C186-03 60
- Extender Modules 61
- 66 C79000-G8976-C186-03 66
- Installing on an S7-300 Rail 68
- Dummy Cover 72
- Removing a Media Module 73
- Variants of the Covers 74
- Fitting a Cover 74
- Removing a Cover 74
- Fitting a Dummy Cover 75
- Removing a Dummy Cover 75
- Specifying the Slot Number 88
- Applying the Slot Numbers 88
- 6.5 Factory Defaults 89
- 6.6 Ports 90
- I N 3I N 4 92
- I N 5I N 8 I N 7 M 5 I N 6 93
- X 4 1 4 - 3 E 94
- 96 C79000-G8976-C186-03 96
- 6.7 Operator Controls 101
- Ring Ports in Slots 5 to 7 103
- R1 and R2 are set to OFF 104
- 6.8 LED Display 106
- Display Modes A through C 109
- Display in Display Mode D 110
- I N 1 / I N 5 111
- Display Modes A through D 112
- Port Statuses in DMode A 113
- Port Statuses in DMode B 114
- Port Statuses in DMode C 115
- Port Statuses in DMode D 116
- 6.9 Replacing the C-PLUG 117
- 6.10 Show Location 118
- Technical Specifications 119
- 122 C79000-G8976-C186-03 122
- 7.6 Extender Module EM495-8 127
- 1 0 7 , 5 128
- 1 0 9 , 5 128
- 1 1 2 , 4 128
- 7.7 Extender Module EM496-4 129
- Approvals, Certificates 131
- EMC Directive 132
- Required FDA and IEC labels 132
- Directive on Machines 133
- Installation Guidelines 133
- Note for Australia 134
- FM Approval 136
- ATEX Approval 136
- Certification 137
- 138 C79000-G8976-C186-03 138
- Glossary 139
- A&D Technical Support 147
- Nuernberg 147
- Johnson City 147
- A&D Technical Support 148
Produits connexes et manuels pour Commutateurs de réseau Siemens X-400
(296 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.383 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels