Siemens X-400 Manuel d'utilisateur Page 76
- Page / 148
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Installation and Commissioning
Operating Instructions for SCALANCE X-400 Industrial Ethernet Switches
76 C79000-G8976-C186-03
6.3 Installing / Removing Extender Modules
6.3.1 Installing / Removing the Twisted Pair Extender
Installing the Twisted Pair Extender on the S7-300 Rail
You require the following tools:
● slotted screwdriver with a 2.8 mm wide blade
● slotted screwdriver with a 5.5 mm wide blade
Note
Make sure that in addition to the extender width of 87 mm, there is a clearance of
20 mm to the right of the basic device on the S7-300 rail to be able to align the
guide bolts of the extender with the holes in the basic device during installation.
When installing a twisted pair extender on an S7-300 rail, the basic device remains
in position. Follow the steps below:
1. Remove the cover from slot 11 of the basic device.
2. Remove the right-hand side panel of the basic device. To do this, use a slotted
screwdriver with a 2.8 mm wide blade to loosen the two captive slug screws on
slot 11 in the upper and lower recesses as far as they will go.
3. Remove the side panel of the basic device from the basic device to the right.
Note
Keep the panel in a safe place in case the extender needs to be removed
again later.
4. Remove the two covers from the extender.
5. Place the extender module on the edge of the S7-300 rail with the upper
groove angled slightly towards the back and tilt the extender towards the back.
Make sure that there is adequate clearance between the guide bolts of the ex-
tender module and the basic device. In this position, the extender module
should not be able to slip off, however it can be moved horizontally in both di-
rections.
- Trademarks 3
- 6 C79000-G8976-C186-03 6
- Preface 7
- Further Documentation 8
- Standards and Approvals 8
- Contents 9
- C79000-G8976-C186-03 10
- Introduction to 11
- Industrial Ethernet Switches 11
- 1.2 Topologies 13
- Electrical Ring 14
- Optical Ring 14
- Configuration Example 15
- 1.2.2 Star Structure 16
- 1.2.3 Line Structure 18
- SCALANCE X-400 21
- M M 4 9 2 - 2 23
- F O 2 x 1 0 0 0 23
- 2.2 Ports of SCALANCE X-400 24
- Transmission medium 25
- Transmission range 25
- Connectors 25
- 2.2.2 1000Base-TX 26
- 2.2.3 100Base-FX 27
- Transmission Range 28
- 2.2.4 1000Base-SX 29
- 2.2.5 1000Base-LX 30
- Compatibility List 31
- 32 C79000-G8976-C186-03 32
- Overview 33
- Components of the Product 35
- Signaling Contact 40
- DI Module 41
- Serial Port 43
- Ethernet Port 43
- Area of Application 44
- How It Works 44
- Diagnostics 45
- Startup Behavior 46
- 4.1 Media Modules 49
- Options for Slot 5 50
- Options for Slots 6 and 7 50
- Properties 51
- Connector 51
- 4.2 Covers, Dummy Cover 55
- CV490 2x1000 56
- Displays of the Cover 56
- CV490 2x100 57
- CV490 4x100 58
- Slot of the Dummy Cover 59
- Displays of the Dummy Cover 59
- 60 C79000-G8976-C186-03 60
- Extender Modules 61
- 66 C79000-G8976-C186-03 66
- Installing on an S7-300 Rail 68
- Dummy Cover 72
- Removing a Media Module 73
- Variants of the Covers 74
- Fitting a Cover 74
- Removing a Cover 74
- Fitting a Dummy Cover 75
- Removing a Dummy Cover 75
- Specifying the Slot Number 88
- Applying the Slot Numbers 88
- 6.5 Factory Defaults 89
- 6.6 Ports 90
- I N 3I N 4 92
- I N 5I N 8 I N 7 M 5 I N 6 93
- X 4 1 4 - 3 E 94
- 96 C79000-G8976-C186-03 96
- 6.7 Operator Controls 101
- Ring Ports in Slots 5 to 7 103
- R1 and R2 are set to OFF 104
- 6.8 LED Display 106
- Display Modes A through C 109
- Display in Display Mode D 110
- I N 1 / I N 5 111
- Display Modes A through D 112
- Port Statuses in DMode A 113
- Port Statuses in DMode B 114
- Port Statuses in DMode C 115
- Port Statuses in DMode D 116
- 6.9 Replacing the C-PLUG 117
- 6.10 Show Location 118
- Technical Specifications 119
- 122 C79000-G8976-C186-03 122
- 7.6 Extender Module EM495-8 127
- 1 0 7 , 5 128
- 1 0 9 , 5 128
- 1 1 2 , 4 128
- 7.7 Extender Module EM496-4 129
- Approvals, Certificates 131
- EMC Directive 132
- Required FDA and IEC labels 132
- Directive on Machines 133
- Installation Guidelines 133
- Note for Australia 134
- FM Approval 136
- ATEX Approval 136
- Certification 137
- 138 C79000-G8976-C186-03 138
- Glossary 139
- A&D Technical Support 147
- Nuernberg 147
- Johnson City 147
- A&D Technical Support 148
Produits connexes et manuels pour Commutateurs de réseau Siemens X-400
(296 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.408 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels