Siemens MC55 Manuel d'utilisateur Page 246
- Page / 469
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
MC55 AT Command Set
10.2 AT+CGANS
s
m
obil
e
MC55_ATC_V01.05 Page 246 of 469 2/10/04
Confidential / Released
Note
• If <response> is 1, the following procedure is followed by the MT:
If the
<L2P> parameter value is unacceptable to the MT, the MT will return an ERROR or +CME ERROR
response. Otherwise, the MT issues the intermediate result code CONNECT and enters V.25ter online data
state.
A
<cid> may be specified for use in the context activation request.
During the PDP startup procedure the MT has the PDP type and the PDP address provided by the network
in the Request PDP context activation message. If this is in conflict with the information provided by a spec-
ified
<cid>, the command will fail. There will be no conflict, if the PDP type matches exactly and the PDP
address given by the context definition for
<cid> is empty or matches exactly with the address specified with
the network PDP context activation message.
The context will be activated using the values for PDP type and address provided by the network, together
with all other information found in the PDP context definition. An APN may or may not be required, depending
on the application.
If no
<cid> is given or if there is no matching context definition, the MT will attempt to activate the context
using the values for PDP type and address provided by the network. The other parameters will be set to their
default values (see
AT+CGDCONT).
If activation is successful, data transfer may proceed.
After data transfer is complete, and the layer 2 protocol termination procedure has completed successfully,
the V.25ter command state is reentered and the MT returns the final result code OK.
In the event of an erroneous termination or a failure to start up, the V.25ter command state is re-entered and
the MT returns the final result code NO CARRIER, or if enabled, +CME ERROR. Attach, activate and other
errors may be reported. It isalso an error to issue the
AT+CGANS command when there is no pending network
request.
The command may be used in both normal and modem compatibility modes.
- Siemens Cellular Engine 1
- Version: 01.05 1
- DocId: MC55_ATC_V01.05 1
- Contents 3
- MC55 AT Command Set 10
- List of Tables 11
- List of Figures 12
- 1. Introduction 13
- 1.2 Related documents 14
- 1.3 Document conventions 15
- 1.3.1 Quick reference table 15
- 1.4 AT command syntax 17
- 1.4.1 Using parameters 17
- 1.5 Supported character sets 19
- 1.6 Flow Control 26
- 1.9 Errors and Messages 29
- 2. Configuration Commands 30
- 2.2.1 AT&V responses 31
- 3. Status Control Commands 63
- 3.2 AT+CIND Indicator control 66
- 4.1 AT\Q Flowcontrol 89
- 4.5 ATE Enable command echo 93
- 4.7.1 Autobauding 98
- 5. Security Commands 103
- 5.2 AT+CPIN2 Enter PIN2 107
- 5.4 AT+CLCK Facility lock 115
- 5.5 AT^SLCK Facility lock 121
- 5.6 AT+CPWD Change Password 122
- 5.7 AT^SPWD Change Password 126
- 6. Identification Commands 127
- 7. Call related Commands 137
- 7.2 ATA Answer a call 139
- 7.10 AT+CHUP Hang up call 152
- 7.16 ATP Select pulse dialing 159
- 7.19 ATT Select tone dialing 162
- 8. Network Service Commands 186
- 8.4 AT+CSQ Signal quality 193
- 8.5 AT^SMONC Cell Monitoring 195
- 8.6.1 AT^MONI responses 198
- 8.6.2 Service states 199
- 8.6.3 Notes 199
- 8.7.1 AT^MONP responses 202
- 8.8 AT^SMONG GPRS Monitor 203
- 8.10 AT^SHOM Display Homezone 207
- 9.5 AT+CCUG Closed User Group 220
- 9.7 AT+CCWA Call Waiting 226
- 10. GPRS Commands 243
- 11. FAX Commands 281
- 11.23 AT+FRM Receive Data 306
- 11.24 AT+FRS Receive Silence 307
- 11.26 AT+FTM Transmit Data 309
- 12.1 SMS parameters 312
- 12.7 AT+CMGS Send SMS message 323
- 13. SIM related Commands 356
- 14.2 ^SSTN SAT Notification 364
- 14.4 AT^SSTR SAT Response 368
- 15. Phonebook Commands 370
- 16. Audio Commands 392
- 16.5 AT+CMUT Mute control 397
- 16.6 AT+VTD Tone duration 398
- 17. Hardware related Commands 425
- 17.2 AT+CCLK Real Time Clock 429
- 18. Miscellaneous Commands 439
- 19. Appendix 443
- 19.2 List of *# Codes 444
Produits connexes et manuels pour Téléphones Siemens MC55
(76 pages)
Téléphones Siemens T25 Manuel d'utilisateur
(41 pages)
(41 pages)
(2 pages)
Téléphones Siemens A400A Spécifications
(11 pages)
(11 pages)
(93 pages)
(48 pages)
© 2020, manymanuals.fr. Tous droits réservés | 3.413 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels