Siemens SIMATIC IPC627C Instructions d'exploitation Page 55
- Page / 210
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
SIMATIC IPC627C
Operating Instructions, 11/2010, A5E02669068-02
55
Integration
8
8.1 Integration into an automation system
The following options are available for the integration in existing or planned system
environments or networks:
Ethernet
The integrated Ethernet port (10/100/1000 Mbps) can also be used for communication and
data exchange with programmable controllers such as SIMATIC S7.
This functionality requires the "SOFTNET S7" software package.
PROFIBUS/MPI
The optional electrically isolated PROFIBUS interface (12 Mbps) can be used to interconnect
distributed field devices or for coupling to SIMATIC S7.
The "SOFTNET for PROFIBUS" software package is required for coupling to S7 automation
systems.
PROFINET
The CP 1616 onboard allows the connection of industrial PCs to Industrial Ethernet. Only
one CP 1616 can be installed in a PG/PC. You will find detailed information in sections
"PROFINET (Page 56)" and "Communications processor CP 1616 onboard (Page 179)".
Device driver CP 16xx.sys
The device driver allow integration of the Windows network protocol in the optional "CP 1616
onboard" Ethernet PROFINET controller on SIMATIC PCs. The PROFINET interface will act
like a regular 100 Mbit Ethernet interface with a MAC address when you use this driver. The
three RJ45 sockets are connected with each other via switch.
PROFINET IO application
You can create, operate and configure PROFINET IO applications using the "Development
Kit DK-16xx PN IO. It must be installed in addition to the CP 16xx.sys device driver. This kit
and the documentation are available free of charge at the following Internet address: DK-
16xx PN IO development kit
(http://www.automation.siemens.com/net/html_00/produkte/040_cp_161
6_d
evlopkit.htm)
SIMATIC NET
You can create, operate and configure SIMATIC installations using this software package.
You will find information on this on the SIMATIC NET Manual Collection CD. This software
package and the documentation are not part of the product package.
Additional information
Additional information is available in the catalog and the online ordering system A&D Mall
(http://www.siemens.com/automation/mall
).
- SIMATIC IPC627C 1
- SIMATIC 1
- Industrial PC 1
- Table of contents 3
- Table of contents 5
- Introduction 10
- Safety notes 11
- Battery 12
- ESD directives 12
- Description 13
- 3.2 Areas of application 14
- 3.3 Benefits 14
- 3.4 Function 15
- 3.5 Features 15
- 3.5 Features 16
- Description 17
- 3.5 Features 17
- 3.7 Design 19
- 3.7 Design 20
- 3.7.2 Operator Controls 21
- On/off button 22
- Interfaces 23
- AC power supply 25
- DC power supply 25
- 6)352),1(7 26
- Status display 27
- Application planning 29
- Rating plate 30
- COA label 30
- Application planning 31
- Mounting 33
- Mounting 35
- Connecting 37
- Localized information 39
- ①, if necessary 40
- ① DC 24 V 41
- ② ground 41
- ③ protective conductor 41
- ① to the device 42
- Commissioning 45
- Switch off the device 46
- 7.5 Notes on operation 47
- 7.5 Notes on operation 48
- Commissioning 49
- 7.5 Notes on operation 49
- Comments about faults 50
- Characteristics 53
- Booting from the Flash drive 53
- Integration 55
- 8.2 PROFINET 56
- Further information 57
- 8.2 PROFINET 58
- Functions 59
- 9.2 Temperature monitoring 60
- 9.3 Watchdog (WD) 60
- 9.4 Fan monitoring 61
- 9.5 Status display 61
- 9.6 SRAM buffer memory 62
- 9.7 Battery monitoring 62
- Function 63
- Requirements 63
- Configuration of the AMT PC 63
- 10.1 Opening the Device 65
- 10.2 Memory expansion 66
- Preparation 67
- Installing a memory module 67
- Removing a memory module 67
- Inserting the slider 69
- 10.4 Installing drives 70
- Preparations 71
- ① on the DVD 72
- ① the drive 73
- ① of the 73
- Installing an SSD drive 74
- Memory expansion options 75
- Opening the board slot 75
- ① and remove 78
- Service and maintenance 81
- Disposal 82
- Replacing the battery 83
- Reconfiguring the BIOS setup 84
- ① from the 85
- ① on the bus 86
- ②. Remove the 87
- Removing the fan 90
- ① on the 91
- Recovery CD or DVD: 92
- Restore DVD: 92
- 11.2.3 Installing Windows 93
- Setting up partitions 94
- Service and maintenance 95
- Drivers & Updates 98
- 11.2.9 Update installation 99
- 11.2.11 CP 1616 onboard 100
- 11.4 BIOS update 101
- 11.5 BIOS Recovery 102
- 12.1 Boot error messages 103
- 12.2 BIOS beep codes 103
- 12.2 BIOS beep codes 104
- 12.2 BIOS beep codes 105
- Special codes 109
- Troubleshooting/FAQs 111
- 13.1 General problems 112
- Troubleshooting/FAQs 113
- Technical data 115
- 14.1 General Specifications 116
- Technical data 117
- Maximum current values 119
- Typical power values 119
- 14.3 AC voltage supply 120
- 14.4 DC power supply 121
- 14.4 DC power supply 122
- Dimension drawings 123
- Dimension drawings 125
- Detailed descriptions 129
- 16.1 Motherboard 130
- Detailed descriptions 131
- 16.1 Motherboard 131
- 16.1.4 External ports 133
- PROFIBUS/MPI interface X4 134
- /(' /(' 135
- DVI-I port, X70 136
- Compact Flash card, X50 137
- 16.1.5 Internal interfaces 138
- 16.1.6 Front ports 140
- Display interfaces 141
- 16.2 Bus board 144
- 16.2 Bus board 145
- 16.2 Bus board 146
- 16.3 System resources 147
- 16.3 System resources 148
- 16.3 System resources 149
- 16.4 BIOS-Setup 153
- Menu layout 154
- 16.4.4 Main menu 155
- 16.4.5 Advanced menu 156
- 16.4 BIOS-Setup 157
- 16.4 BIOS-Setup 158
- Settings in the BIOS 162
- Settings in the MEBx 162
- ME general settings 163
- AMT configuration 164
- 16.4.7 Security menu 165
- 16.4.8 Power menu 166
- 16.4.9 Boot Menu 167
- 16.4.10 Version Menu 170
- 16.4.11 Exit menu 171
- BIOS Setup default settings 172
- 16.5.1 Overview of AMT 175
- 16.5.3 Advanced settings 176
- Procedure 177
- 16.5.6 Forcing user consent 178
- 16.6.1 Introduction 178
- Ethernet 179
- Three RJ45 connectors 179
- CP 1616 onboard as IO device 180
- Firmware 180
- Installation 181
- Loader files 181
- 16.6.2.1 Loading firmware 181
- Start downloading procedure 181
- Example 182
- Configuring 182
- Appendix 183
- ISO 9001 certificate 184
- Software License Agreement 184
- Product safety 184
- A.3 Service and support 185
- A.3 Service and support 186
- ESD guidelines 187
- List of abbreviations 189
- C.1 Abbreviations 190
- List of abbreviations 191
- C.1 Abbreviations 191
- Glossary 195
- Glossary 197
- SIMATIC IPC627C 208
- Index 209
Produits connexes et manuels pour PC/postes de travail Siemens SIMATIC IPC627C
(238 pages)
(52 pages)
(276 pages)
(80 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.740 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels