Siemens MICROMASTER 411 Manuel d'utilisateur Page 50
- Page / 164
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
3 Commissioning Issue 03/01
MICROMASTER 411 & COMBIMASTER 411 Operating Instructions
50
6SE6400-5CA00-0BP0
3.3.4.1 Commissioning with the Basic Operator Panel (BOP)
The Basic Operator Panel (BOP), which is available as an
optional accessory, provides the user with access to the
inverter parameters and enables you to customize the
settings of your COMBIMASTER 411 & MICROMASTER
411. The BOP is mounted in an Operator Panel Mounting
Kit and connected to the COMBIMASTER 411 &
MICROMASTER 411 via the serial interface (see Figure
3-9). The BOP can be used to configure several
COMBIMASTER 411 & MICROMASTER 411 Inverters.
The BOP features a five-digit, seven-segment display for
showing parameter numbers and values, alarm and fault messages and setpoints
and actual values. Parameter sets cannot be saved via the BOP.
Control functions for the inverter (ON/OFF,
, , reverse) are not active in the
works settings. In order to specify this command via the BOP, P0700 = 1 must be
set.
If the BOP connection is removed during normal running the drives is stopped and
the motor coasts to standstill.
Table 3-5 shows the factory default settings for operation via the BOP.
Table 3-5 Default Settings for BOP Operation
Parameter Meaning Default Europe (North America)
P0100 Operating Mode Europe/US 50 Hz, kW (60 Hz, hp)
P0307 Power (rated motor) kW (Hp)
P0310 Motor frequency rating 50 Hz (60 Hz)
P0311 Motor speed rating 1395 (1680) rpm [depending on variant]]
P1082 Maximum Motor Frequency 50 Hz (60 Hz)
- MICROMASTER 411 & 1
- COMBIMASTER 411 1
- Foreword 5
- Definitions and Warnings 6
- Safety Instructions 7
- Transport & Storage 8
- Commissioning 9
- Operation 10
- Repair 10
- Dismantling & Disposal 10
- Table of Contents 11
- List of Tables 13
- List of Illustrations 14
- 1 Overview 15
- 1.2 Design Features 17
- Performance Characteristics 18
- Protection characteristics 18
- 2 Installation 19
- Figure 2-1 Forming 21
- 2.3.1 Preparation 23
- 2.3.2 Installation Procedure 24
- 2 Installation Issue 03/01 26
- Figure 2-5 Cable Glands 27
- COMBIMASTER 411- Case Size B 31
- Motor Poles 32
- 2.5 Electrical Installation 33
- Power Connections 35
- 2.5.4 Motor PTC Connections 38
- Action to Take 39
- 3 Commissioning 41
- +24 V(100 mA max) 43
- 0 V (isolated) 43
- 3.2 General Information 44
- Control Jumpers 48
- 3.3.3 Default setup 49
- 8 9 56
- 3.4.5 If a fault occurs 59
- 4.1 Frequency Setpoint 62
- 4.3.1 OFF1 63
- 4.3.2 OFF2 64
- 4.3.3 OFF3 64
- 4.3.4 DC braking 64
- 4.3.5 Compound Braking 64
- 4.4 Control Modes (P1300) 65
- 4.5 Faults and warnings 65
- 5 System Parameters 67
- 5.1.1 Access Levels 68
- Inverter Unit (P0004 = 2) 70
- Quick Commissioning 70
- Parameter reset 70
- Motor data (P0004 = 3) 71
- Analogue I/O (P0004 = 8) 73
- Drive Features (P0004 = 12) 74
- Motor Control (P0004 = 13) 75
- Communication (P0004 = 20) 76
- PI Controller (P0004=22) 77
- 6 Troubleshooting 79
- 6.3 Faults and Alarms 81
- 6.3.2 Alarm Messages 87
- A0936 PID Autotuning Active 91
- A0952 Belt Failure Warning 91
- 7 Specifications 93
- 7.1 Technische Daten 94
- Table 7-2 Case Size B 95
- Table 7-3 Case Size C 95
- Supply and Motor Terminals 96
- 8 Options 99
- Options 100
- Issue 03/01 8 Options 101
- 8.4 PROFIBUS Module 102
- 8.5 EM Brake Module 103
- 8 Options Issue 03/01 104
- This Chapter contains: 109
- 9.1.1 Self-Certification 110
- 9.1.6 EMC Compliance Tests 113
- 6SE6400-5CA00-0BP0 114
- 10 Engineering Information 115
- Electronic Trip 116
- Overload Limit 116
- Long Term Overload Limit 116
- Continuous Limit 116
- 10.1.2 Fast Current Limit 118
- 10.1.4 I 119
- Frequency 120
- Boost increases 120
- Enabling PI control 122
- PI Feedback signal 122
- PI setpoint 123
- 10.2.4 PI Output Limits 128
- 10.2.5 Further features 128
- 10.2.6 Energy Saving Mode 129
- *p2393Pp 131
- 10.3 Braking 132
- 10.3.1 DC Braking 133
- 10.3.2 Vdc Max Controller 133
- 10.3.3 Compound Braking 134
- Rated Output Current 135
- Input voltage 135
- Rated output current 135
- 10.7 Lifetime of Inverters 137
- 10.8.1 Introduction 138
- 10.8.2 How does BiCo work? 138
- 10.8.4 BiCo Connections 141
- 10.9 Harmonic Currents 145
- 10.11 Power Losses 146
- 10.12 Shock and Vibration 147
- 10.13 PROFIBUS 148
- 10.14 PROFIBUS Module 149
- 10.15.3 PROFIBUS Module 153
- 10.15.6 EM Module 153
- Appendices 155
- A Applicable Standards 155
- B List of Abbreviations 156
- Parts Identification 157
- D Index 158
- User Documentation 161
- Issue 03/01 Geräteansicht 163
- Siemens AG 164
- Bundesrepublik Deutschland 164
Produits connexes et manuels pour Adaptateurs et onduleurs de puissance Siemens MICROMASTER 411
(42 pages)© 2020, manymanuals.fr. Tous droits réservés | 2.591 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels