Siemens MICROMASTER 411 Manuel d'utilisateur Page 120
- Page / 164
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
10 Engineering Information Issue 03/01
MICROMASTER 411 & COMBIMASTER 411 Operating Instructions
120
6SE6400-5CA00-0BP0
10.2 Control and Operating Modes
10.2.1 Boost
Boost is used to increase the output voltage in order to overcome losses and non-
linearity at low frequencies. If the correct amount of boost is applied, the current
and torque will be increased at low frequencies. However, if too much boost is
applied, the motor may overheat if run at low frequencies for a long time and
excessive boost may also saturate the motor, leading to loss of torque.
The I
2
t function helps protect the motor under these circumstances. Boost is
calculated such that 100% boost is the voltage given by:
Stator resistance (P0350) multiplied by rated motor current (P0305).
Which means that changing the value of these parameters will affect the boost
level.
Frequency
Boost increases
voltage here
Voltage
Figure 10-3 Boost-Level
P1310
This parameter sets the % boost applied at 0 Hz. The boost level is then
reduced with increasing frequency to a minimum value, set by P1316,
typically around about 10 Hz.
P1311
This parameter sets a boost voltage, as P1310, except that the boost is
applied only during acceleration, either following a start command or from
set point changes.
P1312
This parameter allows a constant linear boost, again as P1310, to be
applied following a start command only to improve ‘first time’ starting.
Maximum values of P1310, 1311,and 1312 are 250%, but the overall maximum
boost is limited by P0640, the motor overload setting. The boost voltage will also
be limited by the operation of the I
2
t function, so boost may be reduced further if
the motor is in danger of overheating. The progress of the I
2
t function can be
monitored by parameter r0034.
The default settings (P1310 = 50, P1311 and P1312 = 0) allow satisfactory
operation with most loads. Increasing the boost up to say 200% (note that P0640
setting will limit) on smaller motors and 100% on larger motors will often give
improved torque at low frequencies. Use P1311 and P1312 to limit this to
accelerating boost only (e.g. P1310 = 100, P1312 = 100), to reduce the possibility
of overheating.
- MICROMASTER 411 & 1
- COMBIMASTER 411 1
- Foreword 5
- Definitions and Warnings 6
- Safety Instructions 7
- Transport & Storage 8
- Commissioning 9
- Operation 10
- Repair 10
- Dismantling & Disposal 10
- Table of Contents 11
- List of Tables 13
- List of Illustrations 14
- 1 Overview 15
- 1.2 Design Features 17
- Performance Characteristics 18
- Protection characteristics 18
- 2 Installation 19
- Figure 2-1 Forming 21
- 2.3.1 Preparation 23
- 2.3.2 Installation Procedure 24
- 2 Installation Issue 03/01 26
- Figure 2-5 Cable Glands 27
- COMBIMASTER 411- Case Size B 31
- Motor Poles 32
- 2.5 Electrical Installation 33
- Power Connections 35
- 2.5.4 Motor PTC Connections 38
- Action to Take 39
- 3 Commissioning 41
- +24 V(100 mA max) 43
- 0 V (isolated) 43
- 3.2 General Information 44
- Control Jumpers 48
- 3.3.3 Default setup 49
- 8 9 56
- 3.4.5 If a fault occurs 59
- 4.1 Frequency Setpoint 62
- 4.3.1 OFF1 63
- 4.3.2 OFF2 64
- 4.3.3 OFF3 64
- 4.3.4 DC braking 64
- 4.3.5 Compound Braking 64
- 4.4 Control Modes (P1300) 65
- 4.5 Faults and warnings 65
- 5 System Parameters 67
- 5.1.1 Access Levels 68
- Inverter Unit (P0004 = 2) 70
- Quick Commissioning 70
- Parameter reset 70
- Motor data (P0004 = 3) 71
- Analogue I/O (P0004 = 8) 73
- Drive Features (P0004 = 12) 74
- Motor Control (P0004 = 13) 75
- Communication (P0004 = 20) 76
- PI Controller (P0004=22) 77
- 6 Troubleshooting 79
- 6.3 Faults and Alarms 81
- 6.3.2 Alarm Messages 87
- A0936 PID Autotuning Active 91
- A0952 Belt Failure Warning 91
- 7 Specifications 93
- 7.1 Technische Daten 94
- Table 7-2 Case Size B 95
- Table 7-3 Case Size C 95
- Supply and Motor Terminals 96
- 8 Options 99
- Options 100
- Issue 03/01 8 Options 101
- 8.4 PROFIBUS Module 102
- 8.5 EM Brake Module 103
- 8 Options Issue 03/01 104
- This Chapter contains: 109
- 9.1.1 Self-Certification 110
- 9.1.6 EMC Compliance Tests 113
- 6SE6400-5CA00-0BP0 114
- 10 Engineering Information 115
- Electronic Trip 116
- Overload Limit 116
- Long Term Overload Limit 116
- Continuous Limit 116
- 10.1.2 Fast Current Limit 118
- 10.1.4 I 119
- Frequency 120
- Boost increases 120
- Enabling PI control 122
- PI Feedback signal 122
- PI setpoint 123
- 10.2.4 PI Output Limits 128
- 10.2.5 Further features 128
- 10.2.6 Energy Saving Mode 129
- *p2393Pp 131
- 10.3 Braking 132
- 10.3.1 DC Braking 133
- 10.3.2 Vdc Max Controller 133
- 10.3.3 Compound Braking 134
- Rated Output Current 135
- Input voltage 135
- Rated output current 135
- 10.7 Lifetime of Inverters 137
- 10.8.1 Introduction 138
- 10.8.2 How does BiCo work? 138
- 10.8.4 BiCo Connections 141
- 10.9 Harmonic Currents 145
- 10.11 Power Losses 146
- 10.12 Shock and Vibration 147
- 10.13 PROFIBUS 148
- 10.14 PROFIBUS Module 149
- 10.15.3 PROFIBUS Module 153
- 10.15.6 EM Module 153
- Appendices 155
- A Applicable Standards 155
- B List of Abbreviations 156
- Parts Identification 157
- D Index 158
- User Documentation 161
- Issue 03/01 Geräteansicht 163
- Siemens AG 164
- Bundesrepublik Deutschland 164
Produits connexes et manuels pour Adaptateurs et onduleurs de puissance Siemens MICROMASTER 411
(42 pages)© 2020, manymanuals.fr. Tous droits réservés | 2.571 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels