Siemens MICROMASTER 411 Manuel d'utilisateur Page 90
- Page / 164
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
6 Troubleshooting Issue 03/01
MICROMASTER 411 & COMBIMASTER 411 Operating Instructions
90
6SE6400-5CA00-0BP0
CB (communication board) specific
Diagnose & Remedy
See CB user manual
A0709 CB warning 10
Possible Causes
CB (communication board) specific
Diagnose & Remedy
See CB user manual
A0710 CB communication error
Possible Causes
Communication with CB (communication board) is lost
Diagnose & Remedy
Check CB hardware
A0711 CB configuration error
Possible Causes
CB (communication board) reports a configuration error.
Diagnose & Remedy
Check CB parameters
A0910 Vdc-max controller de-activated
Possible Causes
Vdc max controller has been de-activated, since controller is not capable of keeping DC-link voltage
(r0026) within limits (P2172).
Occurs if main supply voltage (P0210) is permanently too high
Occurs if motor is driven by an active load, causing motor to go into regenerative mode
Occurs at very high load inertias, when ramping down
Diagnose & Remedy
Check the following:
Input voltage (P0210) must lie within range
Load must be match
A0911 Vdc-max controller active
Possible Causes
Vdc max controller is active; so ramp-down times will be increased automatically to keep DC-link
voltage (r0026) within limits (P2172).
A0912 Vdc-min controller active
Possible Causes
Vdc min controller will be activated if DC-link voltage (r0026) falls below minimum level (P2172).
The kinetic energy of the motor is used to buffer the DC-link voltage, thus causing deceleration of the
drive!
So short mains failures do not necessarily lead to an undervoltage trip.
A0920 ADC parameters not set properly
Possible Causes
ADC parameters should not be set to identical values, since this would produce illogical results.
Fault value = 0: Parameter settings for output identical
1: Parameter settings for input identical
2: Parameter settings for input do not correspond to ADC type
A0921 DAC parameters not set properly
Possible Causes
- MICROMASTER 411 & 1
- COMBIMASTER 411 1
- Foreword 5
- Definitions and Warnings 6
- Safety Instructions 7
- Transport & Storage 8
- Commissioning 9
- Operation 10
- Repair 10
- Dismantling & Disposal 10
- Table of Contents 11
- List of Tables 13
- List of Illustrations 14
- 1 Overview 15
- 1.2 Design Features 17
- Performance Characteristics 18
- Protection characteristics 18
- 2 Installation 19
- Figure 2-1 Forming 21
- 2.3.1 Preparation 23
- 2.3.2 Installation Procedure 24
- 2 Installation Issue 03/01 26
- Figure 2-5 Cable Glands 27
- COMBIMASTER 411- Case Size B 31
- Motor Poles 32
- 2.5 Electrical Installation 33
- Power Connections 35
- 2.5.4 Motor PTC Connections 38
- Action to Take 39
- 3 Commissioning 41
- +24 V(100 mA max) 43
- 0 V (isolated) 43
- 3.2 General Information 44
- Control Jumpers 48
- 3.3.3 Default setup 49
- 8 9 56
- 3.4.5 If a fault occurs 59
- 4.1 Frequency Setpoint 62
- 4.3.1 OFF1 63
- 4.3.2 OFF2 64
- 4.3.3 OFF3 64
- 4.3.4 DC braking 64
- 4.3.5 Compound Braking 64
- 4.4 Control Modes (P1300) 65
- 4.5 Faults and warnings 65
- 5 System Parameters 67
- 5.1.1 Access Levels 68
- Inverter Unit (P0004 = 2) 70
- Quick Commissioning 70
- Parameter reset 70
- Motor data (P0004 = 3) 71
- Analogue I/O (P0004 = 8) 73
- Drive Features (P0004 = 12) 74
- Motor Control (P0004 = 13) 75
- Communication (P0004 = 20) 76
- PI Controller (P0004=22) 77
- 6 Troubleshooting 79
- 6.3 Faults and Alarms 81
- 6.3.2 Alarm Messages 87
- A0936 PID Autotuning Active 91
- A0952 Belt Failure Warning 91
- 7 Specifications 93
- 7.1 Technische Daten 94
- Table 7-2 Case Size B 95
- Table 7-3 Case Size C 95
- Supply and Motor Terminals 96
- 8 Options 99
- Options 100
- Issue 03/01 8 Options 101
- 8.4 PROFIBUS Module 102
- 8.5 EM Brake Module 103
- 8 Options Issue 03/01 104
- This Chapter contains: 109
- 9.1.1 Self-Certification 110
- 9.1.6 EMC Compliance Tests 113
- 6SE6400-5CA00-0BP0 114
- 10 Engineering Information 115
- Electronic Trip 116
- Overload Limit 116
- Long Term Overload Limit 116
- Continuous Limit 116
- 10.1.2 Fast Current Limit 118
- 10.1.4 I 119
- Frequency 120
- Boost increases 120
- Enabling PI control 122
- PI Feedback signal 122
- PI setpoint 123
- 10.2.4 PI Output Limits 128
- 10.2.5 Further features 128
- 10.2.6 Energy Saving Mode 129
- *p2393Pp 131
- 10.3 Braking 132
- 10.3.1 DC Braking 133
- 10.3.2 Vdc Max Controller 133
- 10.3.3 Compound Braking 134
- Rated Output Current 135
- Input voltage 135
- Rated output current 135
- 10.7 Lifetime of Inverters 137
- 10.8.1 Introduction 138
- 10.8.2 How does BiCo work? 138
- 10.8.4 BiCo Connections 141
- 10.9 Harmonic Currents 145
- 10.11 Power Losses 146
- 10.12 Shock and Vibration 147
- 10.13 PROFIBUS 148
- 10.14 PROFIBUS Module 149
- 10.15.3 PROFIBUS Module 153
- 10.15.6 EM Module 153
- Appendices 155
- A Applicable Standards 155
- B List of Abbreviations 156
- Parts Identification 157
- D Index 158
- User Documentation 161
- Issue 03/01 Geräteansicht 163
- Siemens AG 164
- Bundesrepublik Deutschland 164
Produits connexes et manuels pour Adaptateurs et onduleurs de puissance Siemens MICROMASTER 411
(42 pages)© 2020, manymanuals.fr. Tous droits réservés | 2.757 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels