Siemens SIMATIC PANEL PC 877 Instructions d'exploitation Page 149
- Page / 192
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Troubleshooting and FAQs
12.2 Problems when using modules of third-party manufacturers
SIMATIC Panel PC 577
Operating Instructions, Release 04/2006, A5E00798484-01
12-3
12.2 12.2 Problems when using modules of third-party manufacturers
Problem Possible cause Possible remedy
Check your computer configuration:
• If the computer configuration corresponds with factory state,
contact your technical support team.
• If the computer configuration has changed, restore the
factory state. Remove the third-party modules and reboot
the computer. If the error no longer occurs, the third-party
module was the cause of the fault. Replace this module with
a Siemens module or contact the module supplier.
• Force a “Reset Configuration” using the BIOS setup.
The PC crashes
during startup.
• I/O addresses are assigned
twice.
• Hardware interrupts and/or
DMA channels are assigned
twice
• Signal frequencies or signal
levels are not adhered to
• Different connector pin
assignments
• No “Reset Configuration” in
BIOS-SETUP
If the PC still crashes, contact your technical support team.
- DOCUMENTATION 1
- SIMATIC 3
- Industrial PC 3
- Preface 5
- Related documentation 6
- Conventions 6
- Trademarks 7
- Additional support 7
- Representatives and offices 7
- Training center 7
- Technical support 8
- Table of contents 10
- Table of contents 11
- 1.1 Safety instructions 13
- System expansions 14
- Battery 14
- ESD guidelines 15
- Electrical connection 16
- High frequency radiation 16
- Overview 17
- Transport 17
- Tools & downloads 18
- Processor and CD-ROM drive 18
- Safety-relevant applications 19
- Sources of light 19
- SIMATIC Panel PC 577 20
- 2.1 Application features 21
- 2.2 Design 22
- 2.3 Technical features 23
- Description 24
- Description 25
- 2.3 Technical features 25
- 3.1 Overview 27
- Approvals 29
- 3.4 EMC directive 31
- Planning use 32
- Planning use 33
- 3.5.3 Mounting type 34
- 3.5.4 Degree of protection 35
- 3.6 Mounting cut-out 36
- 3.6.2 Dimensions 37
- 4.1 Securing with clamps 39
- 4.2 Securing with screws 40
- 4.3 Dimensions 42
- 5.1 Overview 43
- 5.2 Interfaces 45
- 5.2.2 Rear interfaces 46
- Power supply 47
- 5.3 Connecting peripherals 48
- USB interface 49
- Using USB peripherals 49
- Connecting USB devices 50
- Principle 51
- Localized information 51
- For USA and Canada: 52
- 110V power supply 52
- 230V power supply 52
- Active PFC 53
- Connecting 54
- Connecting 55
- Commissioning 59
- 6.2 Overview 61
- 6.3 Switching on the device 63
- Commissioning 69
- Service pack 71
- Automatic updates 71
- 7.1 Normal operation 73
- Switching off the device 75
- 7.2.1 Overview 76
- Function 77
- Special features 78
- USB keyboard controller 78
- 7.2.3 KeyTools 79
- 7.2.4 SystemGuard 80
- 7.2.5 TouchInput 81
- 7.2.6 CheckLanguageID 82
- 8.1 Operator controls 85
- "Soft power" key 86
- 8.2.1 Overview 87
- 8.2.2 Keyboard 88
- Function keys and softkeys 89
- Control keys 89
- Alphanumeric keys 89
- Numeric keys 90
- Cursor keys 90
- External keyboards 91
- 3DUW3DUW3DUW3DUW 92
- 3DUW3DUW 92
- 3DUW 3DUW 3DUW 3DUW 92
- 8.3.1 Overview 93
- 8.3.2 Touch screen 94
- 8.4 DVD-ROM drive 95
- Operating 96
- Integration in TIA 97
- 10.1 Servicing 99
- Chemical resistance 100
- Procedure 100
- Carrying out repairs 101
- Limitation of liability 101
- Servicing and maintenance 102
- 10.2.2 Opening the device 103
- Opening the device 104
- Servicing and maintenance 105
- Closing the device 106
- Memory expansion 108
- Installing the memory module 108
- Removing a memory module 109
- 10.2.5 PCI/WinAC cards 110
- PCI card 111
- WinAC card 112
- 10.2.6 Drives 115
- Introduction 122
- Disposal 124
- Preparation 125
- Reconfiguring the BIOS setup 125
- Requirement 126
- Mounting the device 133
- 10.3 Installing software 136
- Restore DVD: 138
- Backing up authorizations 139
- 10.3 Installing software 141
- 11.1 BIOS error messages 145
- Error diagnosing 146
- 12.1 General problems 147
- Troubleshooting and FAQs 148
- Troubleshooting and FAQs 149
- 12.3 SystemGuard errors 150
- 13.1 Technical data 151
- Technical specifications 152
- Technical specifications 153
- 13.1 Technical data 153
- 13.3 Keyboard table 157
- 13.3 Keyboard table 159
- Detailed descriptions 165
- 14.2 Riser card 166
- 14.3 Touch sensor 167
- 14.4 System resources 169
- 14.4.2 Interrupt assignment 170
- 14.5 BIOS setup 171
- A Appendix 173
- EMC directive 174
- Low Voltage Directive 174
- Declaration of conformity 174
- Installation guidelines 174
- Connecting peripherals 174
- DIN ISO 9001 certificate 175
- Software license agreement 175
- Appendix 176
- A.1.3 ESD guideline 177
- Handling ESD modules 178
- Shipping ESD modules 178
- Appendix 179
- A.2 Abbreviations 180
- A.3 Glossary Definitions CU 181
- SIMATIC Panel PC 577 186
- Index 187
- Index 188
- ,'$( 192
Produits connexes et manuels pour PC/postes de travail Siemens SIMATIC PANEL PC 877
(150 pages)
(276 pages)
(80 pages)
(32 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.840 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels