Siemens SIMATIC Box PC 620 Manuel de service Page 89
- Page / 208
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
SIMATIC Box PC 620 Expansions
5-27
SIMATIC Box PC 620 Manual
C79000-G7076-C639-02
5.9 Processor Upgrade
You can boost the performance of your SIMATIC Box PC 620 by installing other
Pentium II processors. Consult your local service partner or distributor.
Note
Processor upgrade
If an upgrade is implemented, for example to a processor with a different
frequency, it may be important to also upgrade the BIOS.
Processor Fixing screws
Figure 5-22 Position of the Processor
Proceed as follows:
1. Open the housing as described in Section 5.1 and remove all the
expansion cards (see Section 5.4.2).
2. Undo the 3 fixing screws (TORX T6) of the module on the motherboard
3. Then you can remove the CPU from the housing.
4. Proceed in the reverse order for assembly.
Note
The processor is available as a replacement part without a heat sink.
- What this Manual is About 3
- Scope of the manual 3
- Approvals 3
- Information Classification 4
- Pointers through the Manual 4
- Further support 5
- Table of contents 10
- Product Overview 11
- Range of Application 12
- Fitting Option 12
- Functions 12
- Further Areas of Application: 12
- Overview of Chapter 15
- Recording the Serial Number 16
- Preferred position 22
- 2.3 Preparing for Operation 23
- 2.4 Transport 25
- Reset Button 30
- 3.3 Ports 31
- Connecting USB Devices 32
- 3.4 PC Card Port 33
- Installing PC Cards 34
- 3.5 Drives 35
- Figure 3-6 Handling Disks 36
- 3.5.3 Hard Disk Drive 37
- Closing the Drawer 38
- 3.6 Backup Battery 40
- Setting Up and Operating the 41
- SIMATIC Box PC 620 41
- Connection to power supply 42
- Inlet connector for non 42
- Power Connection 43
- Country-Specific Information 44
- Connecting Monitors 46
- Using a Mouse 47
- Connecting a PS/2 Mouse 47
- Connecting a Serial Mouse 47
- Connecting a PS/2 Keyboard 48
- Connecting USB Periphery 49
- 4.3 Working with PC Cards 50
- Point-To-Point Connection 53
- (socket) 54
- Jumper Settings 57
- Changing the Jumper Setting 57
- (MPI/DP) 58
- Connecting 59
- MPI/PROFIBUS Network 59
- PROFIBUS 60
- Industrial Ethernet 61
- 4.8 Connection under Windows 61
- SIMATIC Box PC 620 Expansions 63
- 5.1 Opening the Unit 64
- 5.1.1 Prerequisites 64
- Before Opening the Unit 65
- Components 67
- 5.1.5 The Motherboard 69
- Components on the Motherboard 70
- Standard Memory 71
- Installing the SO DIMM Cards 72
- Installation 72
- Battery Voltage too Low 73
- Replacing tthe Battery 73
- Changing SETUP 74
- Notes about the Cards 75
- Note about Long PCI Cards 76
- 5.9 Processor Upgrade 89
- PROFIBUS-DP Network 91
- 5.12 Reset Button 94
- Chapter Overview 95
- SETUP Program 96
- Incorrect SETUP Data 96
- Starting SETUP 96
- SETUP Menus 96
- Menu Structure 98
- 6.1.1 The Main Menu 99
- Uhrzeit und Datum 100
- Disk drive 100
- “Type” Field 101
- “Multi Sector-Transfer” Field 102
- “LBA Mode Control” field 102
- “32 Bit-IO” Field 102
- ”Memory Cache” Field 103
- Option ”Boot Options” 104
- Example of a summary screen: 105
- Option “Keyboard Features” 106
- ”Hardware Options” Field 107
- SIMATIC Box PC 620 Manual 108
- C79000-G7076-C639-02 108
- 6.1.2 The Advanced Menu 109
- Submenu COM/LPT Configuration 110
- Printer Port Internal LPT1 111
- PCI Configuration Submenu 111
- ”PCI Devices” Field 112
- Option “PCI IRQ line” 115
- 6.1.3 The Security Menu 116
- 6.1.4 The Power Menu 118
- 6.1.5 The Boot Sequence Menu 120
- 6.1.6 The Version Menu 122
- 6.1.7 The Exit Menu 123
- 6.1.8 Default Setup Settings 124
- 6.2 Configuring the PC Card 127
- Error Diagnosis 129
- 7.1 Diagnosing Errors 130
- Hardware Information 135
- Basic System 136
- 8.3 Hardware Address Table 138
- I/O Adress Assignment 140
- I/O Address Assignments 141
- DMA Assignments 141
- 8.4 Interrupt Assignments 142
- 8.5 Video Modes 144
- 8.6 Monitoring functions 145
- Temperature Monitoring 146
- 8.6.4 Watchdog (WD) 147
- Function 147
- WD Reactions 147
- WD Monitoring Times TWD 147
- 8.7 Ports 148
- 8.7.1 External Ports 148
- Gender Changer for COM1 150
- Serial Port COM2 (V24/Mouse) 151
- Parallel Port LPT1 152
- PS/2 Mouse Port 153
- USB Port 155
- MPI/DP Socket Connector 156
- Ethernet RJ45 Connection 157
- VGA Socket Connector 158
- Display Port (CMOS, X420) 159
- Display Port (LVDS), X400 161
- Port to the Bus Unit (X1) 165
- 8.8 Bus Board 172
- ISA Slot Pin Assignment 174
- PCI Slot Pin Assignment 176
- 8.9 CD-ROM Drive 178
- CD-ROM Front 179
- Emergency Eject 179
- 8.10 Power Supply (AC) 180
- 8.11 Power Supply (DC) 181
- 8.12 Connecting Cables 182
- Standard Connecting Cable 183
- Adapter for PU 6xx Cable 183
- Overview of chapter 187
- A.1 What does ESD mean? 188
- A.2 Electrostatic charging 189
- Avoid direct contact 190
- Glossary 191
Produits connexes et manuels pour PC/postes de travail Siemens SIMATIC Box PC 620
(259 pages)
(276 pages)
(80 pages)
(32 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.323 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels