Siemens SED2 Manuel de service Page 30
- Page / 154
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
SED2 Operation & Maintenance Manual
22 Siemens Building Technologies, Inc.
Chapter 5 — Commissioning
:$51,1*
• Only authorized personnel trained in the setup, installation, commissioning, and
operation of the SED2 may work on the product and plant.
• SED2 drives operate at high voltages. In some components, operation of electrical
equipment involves using dangerous voltages.
• In cases where faults in the control equipment could cause significant equipment
damage or severe physical injury (such as potentially dangerous short circuits), use
external precautions to ensure and to enforce safe operation (such as independent
limit switches and mechanical interlocks).
• Emergency stop facilities in accordance with EN 60204, IEC 204 (VDE 0113) must
remain functional in all operating modes of the control equipment. Resetting the
emergency stop facility must not result in an uncontrolled or undefined restart. Do not
use the SED2 drive as an emergency stop mechanism (per EN 60204, section
9.2.5.4).
• The equipment incorporates internal motor overload protection in accordance with
UL508C, Section 42. See Motor l2t Temperature Reaction parameter P0610; 1
2
T is
ON by default. Motor overload protection can also be provided with an external PTC
temperature sensor (disabled by default via Motor Temperature Sensor parameter
P0601). For reliable motor overload protection, the motor parameters must be
configured accurately.
• Certain parameter settings can cause the SED2 to restart automatically after a fau
lt or
a power failure (provided the fault is eliminated/acknowledged or the supply voltage is
restored).
- SED2 Operation & 3
- Maintenance Manual 3
- Manual Organization 9
- Manual Notations 10
- Where To Send Comments 10
- Reference Documents 10
- General 11
- Environmental Conditions 13
- Frame Sizes and Power Ranges 14
- Mounting 15
- Frame Size B Frame Size C 17
- Motor Cable Length 19
- Torx driver T20 21
- Power and Motor Connections 22
- :$51,1* 23
- (Ground) 25
- Control Terminal Connections 28
- 5 1 9 2 B 0 1 e n 29
- Chapter 5 — Commissioning 30
- DIP Switch Settings 31
- Prerequisites 32
- SED2 Operator Panels 32
- Buttons on the BOP and AOP 33
- Chapter 5 – Commissioning 35
- Continued 35
- Commissioning Prerequisites 36
- LR 39020 37
- SED2 Operation with the BOP 41
- Testing with the BOP 42
- Testing with the AOP 42
- Chapter 6 — Programming 43
- See AOP 45
- Operating 45
- Instructions 45
- SED2 Basic Functions 46
- DIN6 DIN5 47
- DIN4 DIN3 47
- DIN2 DIN1 47
- Digital Outputs 48
- Analog Inputs 49
- Signal in % 50
- Time in ms 50
- Analog Outputs 51
- P0776, Type of analog output 52
- Frequency Setpoint (P1000) 53
- OFF Functions 54
- SED2 HVAC Functions 55
- CONTROLLER 56
- 5192Z22en 57
- 5192Z23de 59
- Staging Pumps or Fans 60
- Figure 35. Staging Pumps 61
- P2378, Staging frequency 64
- Control (Commissioning) 65
- Chapter 7 — Troubleshooting 67
- Chapter 7 – Troubleshooting 69
- Reading Faults 74
- Resetting Faults 74
- Warning Messages 74
- Chapter 8 — Technical Data 78
- Specification Options 78
- Dimensions and Weights 80
- Unit-specific Data 80
- Options 84
- Overview 85
- Using the Serial Interface 85
- Hardware Inputs and Outputs 86
- Point Database 87
- Ordering Notes 87
- Verifying Parameters 88
- Using the SED2 with SBT (P1) 88
- Strategies for FLN (P1) 88
- Other Functionality 90
- Chapter 9 – Communications 95
- N2 Bus Connections 96
- Inverter Unit (P0004=2) 99
- Motor Data (P0004=3) 100
- Analogue I/O (P0004=8) 101
- Drive Features (P0004=12) 103
- Motor Control (P0004=13) 103
- Communication (P0010=20) 104
- PI Controller (P0004=22) 105
- Factory settings (P0010=30) 106
- Parameter List 107
- Manual Addendum 137
- EMC-Compatibility 139
- 5192Z04en 140
- Shield connected 141
- Motor cable 141
- Incoming mains voltage 141
- 5192J21us 141
- Frame Sizes A through C 142
- Frame Sizes D through F 143
- Connecting Multiple Motors 144
- Chapter 3 - Programming 146
- (Bypass request) 147
- Bypass contactor 147
- VSD contactor 147
- Hibernation Mode 148
- P2392, Restart frequency 149
- Introduction 150
- How does BiCo work? 150
- 125-3202 154
Produits connexes et manuels pour Téléviseurs et moniteurs Siemens SED2
(34 pages)
© 2020, manymanuals.fr. Tous droits réservés | 2.356 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels