Siemens Sinumerik 810T Manuel d'utilisateur Page 81
- Page / 90
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
EMCO WINNC SINUMERIK 810/820 T ALARMS / MESSAGES
H 5
3006 Nxxxx Wrong block structure
Cause: too much M/H/T/D/S/G commands in one
block, G commands of the same group
twice programmed in block, circle with more
than 2 axes or polar coordinate centre
point with more than 2 axes, scale factor
programmed twice in a block, change of
plane / zero offset / tool change / mirror
while contour draft, no valid contour draft
with the programmed addresses
Remedy: correct program
3008 Nxxxx Subroutine error
Cause: subroutine counter invalid
subroutine end with M30
nesting depth override
Remedy: correct subroutine counter
program M17, max. 4 subroutines nested
3011 Nxxxx To many axes/axis twice
Cause: the position (axis) was already program-
med, too much axes with block with thread/
mirror
Remedy: correct program
3012 Nxxxx Block not in memory
Cause: program end without M30, jump target not
found
Remedy: correct program
3021 Nxxxx CRC contour error
Cause: The tool radius is too large in relation to the
smallest contour element, contour violation
with full circle, programmed arc radius
smaller than the tool radius
Remedy: correct program
3042 Wrong picture
Remedy: switch off / on the PC, reprot to EMCO if
repeatable
3049 Wrong simulation area
Cause: With graphik simulation no or an invalid
simulation area was put in
Remedy: put in/correct simulation area
3081 Nxxxx CRC not selected for approaching
Cause: With soft approaching / leaving a contour
G41 or G42 must be active
Remedy: correct program
4100 Nxxxx No D-number active
Cause: cycle alarm: no tooloffset active
Remedy: activate tool correction (D)
4101 Nxxxx Cutter radius = 0
Remedy: enter cutter radius
4102 Nxxxx Cutter radius too large
Remedy: correct cutter radius
4103 Nxxxx Tool to wide
Remedy: L93: use other tool
4120 Nxxxx Spindle rotat. dir. n. progr.
Remedy: L94: program spindle direction
4121 Nxxxx Spindle not in tol. range
4122 Nxxxx Calculated feed too large
Remedy: L841: reduce feed
4140 Nxxxx Fin. part diam. too small
Remedy: alter program
4180 Nxxxx Option not available !
Remedy: order option (L841, L94)
4200 Nxxxx Check definition of R
Remedy: correct R32
6000 - 7999 Machine alarms
see "Machine Alarms"
8004 ORDxx Failure main-drive unit
8005 - 8009 ORDxx Internal error AC
Remedy: report to EMCO if repeatable
8010 ORDxx Syncr. error main drive
Cause: synchronisation mark missing for main drive
Remedy: report to service technician, if repeatable
8011 - 8013 ORDxx Internal error AC
Remedy: report to EMCO, if repeatable
8014 ORDxx Decel.-time of axis too high
Remedy: report to service technician, if repeatable
8018 ORDxx Internal error AC
Remedy: report to EMCO, if repeatable
8021 ORDxx Internal error AC
Remedy: report to EMCO, if repeatable
8022 ORDxx Internal error AC
Remedy: report to EMCO, if repeatable
8023 ORDxx Invalid Z value for helix
Cause: The Z value of the helix must be smaller
than the length of the arc to be traversed
Remedy: Program correction
8100 Fatal init error AC
Cause: Internal error
Remedy: Restart software or reinstall when neces-
sary, report to EMCO, if repeatable.
8101 Fatal init error AC
see 8101.
8102 Fatal init error AC
see 8101.
8103 Fatal init error AC
see 8101.
- Software Description 1
- Contents 3
- E: @-Codes 4
- G: Survey Pages 4
- H: Alarms and Messages 4
- Starting Information 4
- A: Key Description 5
- Key functions 6
- Address and Numeric Keyboard 6
- Machine Control Keys 8
- KEY DESCRIPTION 9
- PC Keyboard 10
- Screen with Softkeys 11
- INNC SINUMERIK 810/820 T 12
- EY DESCRIPTION 12
- B: Basics 13
- Zero Offset 14
- Coordinate System 14
- Input of the 15
- Tool Data Measuring 16
- Cutter position 17
- Input of the Tool Data 18
- Tool Data Measuring with the 20
- Optical Presetting Device 20
- C: Operating Sequences 21
- Approach the Reference Point 22
- Input of the Gear Position 22
- Setting of Language and 22
- Workpiece directory 22
- Input of Programs 23
- PERATING SEQUENCES 24
- Program Administration 25
- Data Input-Output 25
- Program Run 29
- Graphic simulation 31
- D: Programming 33
- Survey of G Commands 34
- Survey of M Commands 34
- Survey of Cycles 34
- Description of G Commands 35
- G01 Linear Interpolation 35
- G02 Circular Interpolation 36
- Clockwise 36
- G03 Circular Interpolation 36
- Counterclockwise 36
- G04 Dwell 37
- G09 Exact Stop 37
- G10 - G13 Polar Coordinate 37
- Interpolation 37
- G25/G26 Programmable working 38
- G33 Thread Cutting 39
- Cutter Radius Compensation 39
- ROGRAMMING 40
- G48 Leave as Approached 42
- G50 Cancel Scale Modification 42
- G51 Scale Modification 42
- G54 - G57 Zero Offset 1 - 4 43
- G58/G59 Programmable Zero 43
- G60 Exact Stop Mode 44
- G63 Thread tapping with 44
- G70 Measuring in Inches 45
- G71 Measuring in Millimetre 45
- G92 Spindle Speed Limit 46
- G90 Absolute Programming 46
- G91Incremental Programming 46
- G94 Feed per Minute 49
- G95 Feed per Revolution 49
- G96 Constant Cutting Speed 49
- G97 Constant Spindle Speed 49
- G131 Transmit 50
- Description of Cycles 55
- L93 Cut-in Cycle 55
- L94 Undercut Cycle 56
- L97 Thread Cutting Cycle 58
- L971 Longitudinal Thread 58
- L98 Deep Hole Drilling Cycle 59
- L99 Thread Draft 60
- Contour definition 61
- Subroutines 63
- R PARAMETER 71
- OFFSET" 73
- Softkey Menu Survey 74
- Survey Guiding 76
- Control Alarms 78
- Machine Alarms 85
Produits connexes et manuels pour Mise en réseau Siemens Sinumerik 810T
(187 pages)
Mise en réseau Siemens MC35 Spécifications
(42 pages)
(42 pages)
Mise en réseau Siemens SE505 Spécifications
(135 pages)
(135 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.166 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels