Siemens TC65 Manuel d'utilisateur

TC65Smart User Manual Rev. 2-1.0 1 TC65Smart

TC65Smart User Manual Rev. 2-1.0 10 2.Connection of the Device to the Target System. Clause 2.1, Table 2.1, Fig. 2.2 Clause 2.4, Table 2.4,

TC65Smart User Manual Rev. 2-1.0 11 5.GND 4.DTR1.DCD 3.TxD 2.RxD 8.CTS9.RI 6.DSR 7.RTS Рис. 2.2 Table 2.1 Contact Signal Direction Level

TC65Smart User Manual Rev. 2-1.0 12 2.2. Connector RJ-11 for Connection of the Two-Wire UART. It is used for connection of the accessories to A

TC65Smart User Manual Rev. 2-1.0 13 2.3. Connector RJ-11 for Headset Connection. It is designed for connection of the phone receiver or a heads

TC65Smart User Manual Rev. 2-1.0 14 2.4. Discontinuous Terminal Connector. The Terminal is powered and it exchanges the information with the

TC65Smart User Manual Rev. 2-1.0 15 Table 2.4 Terminal Signal Type Corresponding signal of the module TC65 (numbers of the connector contacts a

TC65Smart User Manual Rev. 2-1.0 16 Fig. 2.5 Connection of the discontinuous terminal connector.

TC65Smart User Manual Rev. 2-1.0 17 3.Operation of the Terminal Major Assemblies. 3.1. Backup Controller. It performs the following functi

TC65Smart User Manual Rev. 2-1.0 18 As Fig. 3.1 shows, the backup controller receives the following signals: • Bus-line I2C with TC65 of the GS

TC65Smart User Manual Rev. 2-1.0 19 • The DTR signal from the interface level converter RS-232 («Serial1», ASC0 TC65). This signal coming f

TC65Smart User Manual Rev. 2-1.0 2 Contents Contents...

TC65Smart User Manual Rev. 2-1.0 20 Table 3.1 Command Byte code (HEX) Operand byte Action Command I2C terminal TC65 (example) TC65_reset 0x01

TC65Smart User Manual Rev. 2-1.0 21 TC65_DTR_OFF0x12 0x00-0xFF The command sets up the mode of hardware disabling of the enabled module by the

TC65Smart User Manual Rev. 2-1.0 22 3.2. SIM Card Switch and SIM mounts. “tray”2 Indicator SIM1 Indicator SIM2 Extracting buttons “SIM2” “S

TC65Smart User Manual Rev. 2-1.0 23 3.2.1. By transmission of the command from TC65 through the bus-line I2C (see Table 3.1). This way makes it

TC65Smart User Manual Rev. 2-1.0 24 3.3. Power Supply Control of the Module TC65. In addition to the regular methods of power supply control o

TC65Smart User Manual Rev. 2-1.0 25 3.4. Indication Mechanisms. The Terminal is equipped with 4 LED indicators for visual control of operation.

TC65Smart User Manual Rev. 2-1.0 26 4.Supplementary Literature. Whereas the terminal “TC65Smart” is based upon the GSM module Siemens TC65, sup

TC65Smart User Manual Rev. 2-1.0 3 1.General Information. 1.1. Purpose of the Device The terminal TC65Smart is an industrial quad-band GSM mo

TC65Smart User Manual Rev. 2-1.0 4 1.2. Parameters General Parameters  Radio frequency ranges: GSM 850 / 900 / 1800 / 1900  GSM Release

TC65Smart User Manual Rev. 2-1.0 5 Java ™ parameters  CLDC 1.1 Hl  J2ME™ with support IMP 2.0  Protected data transmission with HTTPS

TC65Smart User Manual Rev. 2-1.0 6 1.3. Exterior Appearance of the Device The housing of the device is made of metal, the control elements ar

TC65Smart User Manual Rev. 2-1.0 7 1.4. External Connectors and Indication Elements. 13 2 74 9 65 8 1011 Fig. 1.3 Connectors and indication e

TC65Smart User Manual Rev. 2-1.0 8 1.5. Functional Diagram. 2134 5-8 1011External interface Control assembly Housing Fig. 1.4 Fig. 1.4 repre

TC65Smart User Manual Rev. 2-1.0 9 o Interface LVUART (UART with TTL/CMOS-consistent signal levels). • Backup drive controller; • Indication