Siemens S6 GSM Manuel d'utilisateur

Data & FaxFunctionalityof theSIEMENS Combiset GSM.

10Refer to Section 4 to create a Remote Access Connection to your Internet Service Provider. Oncecompleted verify the connection properties by method

11Go to ‘Edit-Preferences-Advanced-Proxies’ and select ‘Direct connection to the Internet’. Confirm,Return to Browser screen and in the ‘Location’ bo

12• Terminal line settingsCurrently, the GSM module handler is set to 9600 bps, 8 bits data, 1 bit stop, no parity, RTS/CTS flowcontrol. Please use t

13Direct dialling from a phonebook location (stored in SIM card) can be done with the followingcommand:ATD>17; or ATD>SIM17; (voice call here)AT

14Application to GSM AT+VTS=AGSM to application OK command validApplication to GSM AT+VTS=11GSM to application +CME ERROR:4 if the <Tone> is wro

15Application to GSM ATDL Redial last numberGSM to application OK +49897220; Last Call was a speech call command valid7.1.8 Signal Quality +CSQThis c

16All others S-parameters (S6, S7, S8 ...) are not implemented.7.1.11 Gain control +VGR, +VGTThis command shall be used by the application to tune the

177.2.3 Request revision identification +CGMRThis command is used to get the software version.Application to GSM AT+CGMR get software versionGSM to ap

18When the application wants to re-start the module (after having done a AT+CFUN=0 command, andwithout having cut the power supply), it has to send:AT

19+CPIN:SIM PIN PIN is required+CPIN: SIM PUK PUK is required+CME ERROR:<err> SIM failure (13) absent (10) etc...The state „SIM PIN“ is entere

21 Prerequisites and Recommendations ... 41.1 Computer HW and S

20The password length is given with the AT+CPWD = ? command.Application to GSM AT+CLCK=“SC“, 1, 1234 enable PINGSM to application OK PIN was rightAppl

217.2.12 Read phonebook entries +CPBRThis command returns phonebook entries for a location range from the current phonebook memorystorage selected w

22<oa> Originator address.<pid> Protocol identifier.<pdu> Binary string coded as specified in document [4]<ra> Recipient add

23The chosen format is stored in E2PROM by the command +CSAS.Application to GSM AT+CMGF? current message formatGSM to application +CMGF:1OKText modeAp

24Application to GSM AT+CRES RestoreGSM to application OK command correct7.3.7 Select TE character set +CSCSThis commands informs the ME which set is

251 SMS-STATUS-REPORT are routed using unsolicited code:+CDS: <pdu> (if PDU mode chosen)or+CDS: <fo>, <mr>[, <ra>, <tora>

26Application to GSM AT+CMGR=2read + bad indexGSM to application +CMS ERROR: 321error : invalid indexApplication to GSM AT+CMGR=1in PDU modeGSM to app

27Hello, how are you ?<ctrl-Z>GSM to application +CMGS : <mr>OKSuccessful transmissionApplication to GSM AT+CMGS=<length><CR>&

28Hence, the application has to indicate this address at initialisation. This address then remains validuntil changed by the application.For example,

29AT+CCFC=<reason>,<mode>[, <number>]<reason> :0 unconditional1 mobile busy2 no reply3 not reachable4 all call forwarding5 all

37.5.1 Bearer type selection +CBST ... 327.5.2 Report control +CR,

307.4.3 Modify SS password +CPWDThis command shall be used by the application to change the supplementary service password. Thesyntax is:AT+CPWD=<

310 CLIR not provisioned1 CLIR provisioned2 Unknown (no network)Application to GSM AT+CLIR=2GSM to application OK command validApplication to GSM AT+C

32Application to GSM AT+COLP=0 Deactivate COLPGSM to application OK command valid7.5 AT commands for Data7.5.1 Bearer type selection +CBSTThe syntax

33GSM to application OK command validApplication to GSM AT+CR=1 extended reports enabledGSM to application OK Command validThe Default value is stored

347.5.7 DCE response format VDetermines the DCE response format, with or without header characters <CR><LF>, and with the useof numerical

35Application to GSM ATZGSM to application OK command valid7.5.11 DTE-DCE local flow control +IFCThis command is used to control the operation of lo

36Application to GSM AT&W writes current configuration to E2promGSM to application OK command valid7.5.16 Radio link protocol parameters +CRLPT

37Application to GSM AT+CEER ask for reason of releaseGSM to application +CEER : Error <xxx>OK<xxx> is the cause informationelement values

3818 No user responding19 User alerting, no answer21 Call rejected22 Number changed26 Non selected user clearing27 Destination out of order28 I

397.7.6 GSM 04.11 Annex E-2: Mobile originating SM-transferCause no 1: "Unassigned (unallocated) number"This cause indicates that the destin

41 Prerequisites and Recommendations1.1 Computer HW and SW requirements/recommendationsThe underneath PC requirements describes the minimum baseline t

40Cause no 47: "Resources unavailable, unspecified"This cause is used to report a resource unavailable event only when no other cause applie

417.7.7 Summary of result codesVerbose result code Numeric(V0 set)Description+CCCM : <ccm> as verbose Current Call Meter value+CCWA : <nb&g

5– BS26, (9600 baud, V110 and V32)– BS25, (4800 baud, V32)– BS24, (2400 baud, V110 and V22bis)• PIN NumberThe PIN number deserves a prominent discussi

6Indicate in the following window that the modem will be manually selected by clicking the checkbox.The next installation window lists modem types and

7Verify once more that the appropriate 'COM port' is selected, as well as that the 'Maximum speed' isset to 9600 bps. Then choose

8The modem test will take a few seconds after which the 'Test Results/Details' window should show alltests 'OK'.The modem driver i

9Select ‘New Connection’ and enter a name for the Remote Connection which you are now creating.(ex. My Service Provider). As driver choose the ‘Stand