Siemens ET 757 E Series Instructions d'exploitation Page 41
- Page / 190
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Installation
4.3 Mounting the interface module
ET 200pro FC
Operating Instructions, 11/2007, A5E01100763B AA
41
4.3 Mounting the interface module
The interface module connects ET 200pro to PROFIBUS DP/ PROFINET IO and supplies
power to the electronic modules.
Requirements
● Interface module for PROFIBUS DP
– The terminating module is removed from the interface module.
– The rack has been mounted.
● Interface module for PROFINET IO
– The terminating module is removed from the interface module.
– The SIMATIC Micro Memory Card is inserted.
– The rack has been mounted.
Required Tools
Cross-tip screwdriver, size 2
Procedure
1. Snap-mount the Interface module onto the rack, then slide it into the correct position
2. Screw-mount the Interface module onto the rack.
Interface module for PROFIBUS DP (without connection module):
2 recessed head screws on the front: top and bottom, tightening torque 1.5 N/m
Interface module for PROFINET IO:
All recessed head screws on the front: top and bottom, tightening torque 1.5 N/m
- ET 200pro FC 1
- Product Information 2
- SIMATIC ET 200S FC 2
- SIMATIC ET 200pro FC 2
- SIMATIC 3
- Frequency converters 3
- Foreword 5
- Validity of the manual 6
- Experience required 6
- Recycling and disposal 6
- Special notes 6
- Foreword 7
- A&D Technical support 8
- Online Service and support 8
- Europe/Africa (Erlangen) 8
- America (Johnson City) 8
- Asia/Pacific (Beijing) 8
- Contact address 9
- Regional contacts 9
- Table of contents 11
- Table of contents 13
- Safety information 17
- Transport and storage 19
- Repairs 19
- 2.1 The frequency converter 21
- Commissioning functions 22
- Interfaces 23
- Operating functions 23
- Function modules 23
- Protective functions 23
- 24
- Description 29
- 2.4 Overview of the LEDs 30
- 33
- 3.1.1 Optical interface 34
- 3.2 PTC/KTY84 interface 35
- Installation 37
- 4.2 Mounting the racks 38
- Tools required 39
- Accessories required 40
- Required Tools 41
- Procedure 41
- 4.4 Mounting the bus module 43
- Required tools 44
- Installation 45
- Motor cable 53
- Power transmission 53
- Procedure: 54
- Figure 5-1 Master system 60
- Figure 5-4 Configuration 61
- Address/ID 62
- Parameter 63
- Figure 5-8 Parameter 64
- Specifying the device name 67
- Figure 5-15 Configuration 68
- Figure 5-19 Parameter 71
- Parameter description 75
- Commissioning (hardware) 77
- 6.1 Startup of ET 200pro 78
- IEC motor 80
- NEMA motor 80
- Entering the type plate data 81
- 7.1 Commissioning sequence 83
- 7.1 Commissioning sequence 84
- 7.2.1 General 85
- STARTER projects 86
- Parameter settings 90
- General settings 91
- Temperature encoder 92
- JOG frequency 93
- Additional setpoints 93
- 6NLSIUHTXHQF\ 94
- Fieldbus parameter 96
- Process data monitoring 97
- P2040 telegram failure time 97
- Control word 1 (STW1) 98
- Status word 1 (ZSW1) 100
- 7.4.2.2 Examples 101
- ET 200pro FC 102
- 7.4.3.1 Block call 103
- 7.4.3.2 Examples 109
- General steps 115
- Description 117
- Acceptance test 117
- Checksums 117
- Functional test 118
- Completing the report 118
- Appendix 118
- Overview 119
- 7.6.1 Factory settings 120
- Required parameter settings 121
- Requirements 123
- Internal memory 124
- External memory 124
- Download 125
- Supplementary conditions 125
- Manual download 127
- Automatic download 128
- See also 130
- Fault codes 131
- Remedy for F00395 131
- 8.2.1 Application ID 133
- 8.2.2 Series commissioning 134
- Frequency converter with MMC 136
- Normal startup without MMC 137
- Normal startup with MMC 137
- Interrupts 139
- Resetting fault codes 139
- Status display through LEDs 140
- Description of the LEDs 141
- Standard functions 141
- 9.2 Diagnostics through LEDs 142
- Prerequisites 144
- Evaluating 144
- 9.5 Device diagnostics 145
- 9.6 Fault clearance 145
- 10.1 Technical data 147
- Ambient conditions 148
- Shocks and vibrations 149
- Air pollution/water 149
- Installation and cooling 149
- 11.1 Frequency converter 151
- 11.2 Bus module 152
- Spare parts/accessories 153
- Power jumper connector 154
- Sealing cap for power bus 154
- A.1 Acceptance Log 155
- A.1 Acceptance Log 156
- Executing the test 157
- Appendix 159
- A.1 Acceptance Log 159
- Data back-up/archiving 162
- Signatures 162
- A.2 ESD directives 163
- Environment 1 164
- Environment 2 164
- Class C1 164
- Class C2 164
- EMC emitted interference 165
- Harmonic currents 165
- EMC immunity 166
- A.2 ESD directives 167
- A.2 ESD directives 168
- A.3 Standards 170
- B.1 Abbreviations 171
- B.1 Abbreviations 172
- B.1 Abbreviations 173
- Glossary 181
- Load groups 182
- Monitoring cycle 182
- Monitoring parameters 182
- Parameter attributes 182
- Changeable in 183
- Data types 183
- Quick commissioning 184
- Range of values 185
- Data sets 185
- Potential groups 185
- Switch-off signal paths 185
- Upload and download 186
- Writable parameters 186
Produits connexes et manuels pour Plaques chauffantes Siemens ET 757 E Series
(76 pages)
(70 pages)
(20 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels