Siemens SICLOCK TC 400 Instructions d'exploitation Page 110
- Page / 138
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Messages
12-109
© Siemens AG 2007 All Rights Reserved
SICLOCK
®
TC400
Processor has not been updated
System and
information
A processor update has been performed, but the processor could not be updated.
Hardware time set
Information The SICLOCK TC400 internal hardware clock has been set.
No useable NTP server
Information A preferred server has not been found.
No hardware time
Application A valid time could not be read from the hardware.
Critical temperature exceeded
Application The critical module temperature has been exceeded
See also Temperature (Section 9.3.5).
Link down EHT1, Link down EHT2, Link down EHT3, Link down EHT4
Application The monitoring of the link status has determined the "Link down" status.
The tripping of an archive entry or alarm can be set, for example, for Ethernet 1 via the
following parameter:
/Network Settings/Ethernet 1/Advanced Settings Adapter 1/monitor link state
(0.05.09)
Microstepping ignored
Application A microstepping has been avoided once by the user.
See also Synchronization (Section 9.3.2).
NTP server selected
Information An NTP server has been selected.
NTP server unreachable
Information The server is no longer available.
Parameter has been reset to factory setting by HMI
Information A parameter has been reset to the factory setting by the HMI. The parameter number is
specified in the message text.
Parameter has been written by HMI
Information A parameter has been written by the HMI. The parameter number is specified in the
message text.
Sector in parameter memory cleared
System An automatic data clearance has been performed in the parameter memory.
Stabilized synchronization
Information New stabilizer data is available and is displayed in the message.
Synchronization inconsistent
Information The consistency check of an external synchronization was negative. The external syn-
chronization and the negatively checked offset are displayed.
Table 12-1 Message overview with event type and brief description
- SICLOCK TC400 1
- Plant Central Clock 1
- TC400 Operating Instructions 4
- Preface-4 5
- Table of contents 6
- Contents-8 9
- Safety Information 1 10
- TC400 11
- SICLOCK 11
- Safety Information 13
- Description 2 14
- Description 15
- 2.2 External synchronization 16
- 2.3 Time receivers 17
- 2.4 Time management 19
- 2.5 Commissioning 19
- 2.6 Redundancy 20
- Hardware Description 3 22
- 3.2 Connection elements 23
- Hardware Description 25
- (Section 8) 25
- 3.4 Scope of delivery 26
- Operation Planning 4 28
- 4.4.3 Fixing method 33
- Installation 5 34
- Installation 35
- Connecting 6 36
- 6.3.1 SICLOCK GPS1000 40
- RADIO CLOCK 1 41
- 6.3.3 SICLOCK GPSDEC 42
- 6.3.4 Third-party systems 43
- 77<DFWLYH 44
- Figure 6-7 OUTPUT 3 RS422 45
- Table 6-4 OUTPUT 3 terminals 45
- Terminal Designation 45
- 5OUTPUT 3A 45
- 6OUTPUT 3B 45
- Configuration Tool 7 48
- Figure 7-2 Parameter view 50
- 7.1 Menus 51
- Configuration Tool 52
- 7.2 General functions 53
- 7.2.2 Authorization 55
- 7.3 Parameters 56
- 7.3.3 Editing parameters 61
- 7.4 Archive 64
- 7.4.2 Filter 68
- 7.5 Troubleshooting 69
- 8.1 Operating display 73
- Figure 8-5 Operating sequence 75
- Password: 76
- 0000000000 76
- 8.2.2 Parameter list 77
- ↑ ↓ to the desired parameter 78
- ∀→" sign 78
- →Language 78
- Parameterization 9 80
- 9.1.2 Operation as NTP client 82
- 9.1.3 Redundancy 83
- 9.2.1 NTP server service 84
- 9.2.2 SIMATIC method 85
- 9.3.1 Time management 89
- 9.3.2 Synchronization 90
- 9.3.3 Display 91
- 9.3.4 System 91
- 9.3.5 Temperature 92
- 9.3.6 Battery 92
- Parameterization 93
- Parameter Table 10 94
- offset Min: 95
- Parameter Table 100
- Service and Maintenance 11 106
- 11.3 Software update 107
- Messages 12 108
- Messages 109
- (0.05.09) 110
- Technical Data 13 112
- Technical Data 113
- Dimension Drawing 14 116
- Dimension Drawing 117
- Circuit Diagrams 15 118
- Circuit Diagrams 119
- Spare Parts / Accessories 16 120
- Spare Parts / Accessories 121
- Appendix A 122
- ESD Guidelines B 124
- ESD Guidelines 127
- List of Symbols C 128
- List of Symbols 129
- Glossary D 130
- Glossary 135
- 90026 N85(0%(5* 138
- *(50$1< 138
Produits connexes et manuels pour Horloges murales Siemens SICLOCK TC 400
(106 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.145 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels